Diagnose soonInterface module faults can mask real battery problems - diagnose the pack first.
The control module managing your high-voltage battery's connection to the car is misbehaving. Expect warnings and limited operation. Usually the module itself or its wiring - qualified tech work.
Key facts
P2C8B means hybrid/EV Battery Interface Control Module B Performance. The control module managing your high-voltage battery's connection to the car is misbehaving. Expect warnings and limited operation. Usually the module itself or its wiring - qualified tech work. WrenchFair's published fair-price range for this repair is $300–$1200 parts and $300–$600 labor at independent shops.
WrenchFair rates P2C8B a 5-of-5 DIY difficulty (“Module diagnosis for the curious; replacement and programming for a qualified tech.”) with a “Diagnose soon” driveability rating: Interface module faults can mask real battery problems - diagnose the pack first. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2024–2024 Acura ZDX (all) — 12V battery keeps discharging (BECM software, TSB 25-025):Factory-documented
Dealer-only diagnosis and repair: the fix is a Battery Energy Control Module software update plus a manual reset procedure, done with Acura's diagnostic tools. But knowing the symptom pattern tells you what to ask for at the service desk.
Do this test first: Do not open, probe, or service the high-voltage system yourself - it carries lethal voltage. Diagnose only up to the low-voltage control side; anything involving the pack, contactors, inverter, or orange HV cabling is qualified-technician work.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2C8B on the 2024–2024 Acura ZDX — but the community-sourced 12V battery keeps discharging (BECM software, TSB 25-025) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
The telltale pattern: the Malfunction Indicator Lamp comes on, or a 'Service High Voltage' message appears, and the 12-volt battery drains intermittently or constantly even though the big battery is fine. Scan codes P2C8A and/or P2C8B (plus U3577 through U3580 and U35AF) point at this bulletin; the bulletin only applies if all of the listed codes are set.
The root cause is an internal Battery Energy Control Module calibration anomaly, not a bad 12V battery. Replacing the 12V battery on its own will not fix it.
The published fix is a BECM software update followed by the manual reset procedure performed twice, then a 12V battery charge-and-test. Warranty time is about 0.4 hour for the programming plus the resets.
This is the ZDX version of the same BECM issue covered on the platform-sibling Honda Prologue (Honda bulletin 25-043). The Acura bulletin applies to all 2024 ZDX trims.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Warranty time is about 0.4 hour for the programming plus the resets.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
hybrid/ev warning on
reduced power
possible no-start
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failing battery interface control module B (most common)
Damaged wiring or corroded connector
Software fault (check for updates before replacing)
Actual battery fault the module is reacting to (fix pack codes first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Do not open, probe, or service the high-voltage system yourself - it carries lethal voltage. Diagnose only up to the low-voltage control side; anything involving the pack, contactors, inverter, or orange HV cabling is qualified-technician work. Tests: Failing battery interface control module B (most common)
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor. - fix any battery pack codes first; the module may be reacting to them. Tests: Actual battery fault the module is reacting to (fix pack codes first)
Check for software updates for the module. Tests: Software fault (check for updates before replacing)
Inspect the module wiring and connectors (depowered, per the service manual). Tests: Damaged wiring or corroded connector
Have a qualified EV technician replace and program the module if needed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2024–2024 Acura ZDX: 12V battery keeps discharging (BECM software, TSB 25-025) — test first, then buy for this job.
The price range below is a national planning range for P2C8B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$300 – $1200
Labor$300 – $600
Battery interface control module B replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2C8B ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Module diagnosis for the curious; replacement and programming for a qualified tech.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →