P2B29: Hybrid/EV Battery Pack Coolant Pump A Overspeed - Dry Run
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA dead pump overheats expensive electronics - fix it before the protection limits become permanent damage.
An electric pump cooling your hybrid/EV's electronics or battery is not doing its job. The car limits power to protect things. It may be running dry - check the coolant level immediately.
Key facts
P2B29 means hybrid/EV Battery Pack Coolant Pump A Overspeed - Dry Run. An electric pump cooling your hybrid/EV's electronics or battery is not doing its job. The car limits power to protect things. It may be running dry - check the coolant level immediately. WrenchFair's published fair-price range for this repair is $100–$400 parts and $150–$400 labor at independent shops.
WrenchFair rates P2B29 a 3-of-5 DIY difficulty (“High-voltage safety first; pump swaps need a proper bleed of the loop.”) with a “Diagnose soon” driveability rating: A dead pump overheats expensive electronics - fix it before the protection limits become permanent damage. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
hybrid/ev warning on
reduced power / turtle mode
its cooling loop running hot
Likely causes
Failed battery pack coolant pump A (most common)
Low coolant level or air in the loop - dry-run overspeed points here first
Blown fuse, damaged wiring, or corroded connector
Control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Do not open, probe, or service the high-voltage system yourself - it carries lethal voltage. Diagnose only up to the low-voltage control side; anything involving the pack, contactors, inverter, or orange HV cabling is qualified-technician work. Tests: Control module fault (rare - diagnose everything else first)
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
Check the battery pack coolant level and bleed air from the loop first - especially for dry-run codes. Tests: Low coolant level or air in the loop - dry-run overspeed points here first
Check the pump A fuse, wiring, and connector. Tests: Blown fuse, damaged wiring, or corroded connector
Command the pump with a scan tool and verify flow.
Replace the pump if it will not run correctly, bleed the loop, clear the code, and confirm normal operation.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$100 – $400
Labor$150 – $400
Hybrid/EV battery pack coolant pump A replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2B29 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — High-voltage safety first; pump swaps need a proper bleed of the loop.
Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.
Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →