P2B24: Hybrid/EV Electronics Coolant Temperature Sensor C Circuit
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonReduced power is the protection strategy working - fix the sensor to get full power back.
Your hybrid/EV cools its power electronics with liquid, and the temperature sensor watching that loop is giving a bad reading. The car will limit power to protect the electronics. Usually the sensor or its wiring.
Key facts
P2B24 means hybrid/EV Electronics Coolant Temperature Sensor C Circuit. Your hybrid/EV cools its power electronics with liquid, and the temperature sensor watching that loop is giving a bad reading. The car will limit power to protect the electronics. Usually the sensor or its wiring. WrenchFair's published fair-price range for this repair is $60–$200 parts and $120–$300 labor at independent shops.
WrenchFair rates P2B24 a 3-of-5 DIY difficulty (“High-voltage safety first, then it is sensor testing and replacement.”) with a “Diagnose soon” driveability rating: Reduced power is the protection strategy working - fix the sensor to get full power back. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine or hybrid warning on
reduced power / turtle mode
cooling fans running hard
Likely causes
Failed electronics coolant temperature sensor C (most common)
Damaged wiring or corroded connector
Low coolant or air in the electronics loop skewing the reading (check the level first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Do not open, probe, or service the high-voltage system yourself - it carries lethal voltage. Diagnose only up to the low-voltage control side; anything involving the pack, contactors, inverter, or orange HV cabling is qualified-technician work.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
Check the electronics coolant level first - low coolant makes sensors lie. Tests: Low coolant or air in the electronics loop skewing the reading (check the level first)
Inspect the sensor C wiring and connector. Tests: Damaged wiring or corroded connector
Compare the reading against a plausible value per the service manual.
Replace the sensor if it reads wrong, bleed the loop, clear the code, and confirm normal readings.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $200
Labor$120 – $300
Hybrid/EV coolant temperature sensor C replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2B24 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — High-voltage safety first, then it is sensor testing and replacement.
Torque specs: Thermostat housing bolts: typically 8–12 Nm. Aluminum threads strip easily — verify spec and use a torque wrench.
Pro tip: Bleed the cooling system per the factory procedure after refilling, or trapped air will overheat the engine and fake a “still broken” reading.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →