P2290

P2290: Injector Control Pressure Too Low

For your specific vehicle: P2290 on a 2011–2016 Chevrolet Silverado HD · 2011–2016 GMC Sierra HD

DIY difficulty 5/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

There is not enough oil pressure to run the high-pressure fuel injection system - on diesels this points to low oil, oil pump, or engine timing problems.

Model notes: Seen on 2003 Ford 6.0L F-250 (died on freeway, hard start). Applies to Ford, Range Rover, BMW, Peugeot.

Key facts

Symptoms

Likely causes

Owner notes linked to P2290: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 8 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Research technical service bulletins for the specific vehicle first.
  2. Make sure the engine is filled to the appropriate oil level and no oil pressure or oil level lamps are illuminated; if they are, perform a manual oil pressure test. Tests: Defective high-pressure injection pressure switch
  3. Retrieve all stored codes and freeze frame data, record them, then clear codes and test-drive until the code restores or the PCM enters readiness mode.
  4. Visually inspect related wiring and connectors; repair or replace wiring that has been cut, burned, or damaged.
  5. Use the DVOM to test voltage and ground circuits at the injection system pressure sensor; check system fuses if no voltage.
  6. If voltage is present, test the corresponding circuit at the PCM connector; an open circuit between the sensor and PCM is suspect if absent there.
  7. Test the injection pressure sensor with the DVOM against manufacturer specifications; replace if non-compliant.
  8. Note: although listed for some gasoline applications, this code is seen almost exclusively in diesel applications with an engine timing and/or lubrication issue.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$50 – $600
Labor$150 – $800

High-pressure injection pressure sensor replacement; oil pump or engine timing repairs cost more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2290 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

5 of 5 — Diesel high-pressure injection and oil pressure diagnosis requires gauges, factory data, and experience.

Watch this repair on YouTube

Parts & tools

Fuel system toolkit — what the job actually takes

Torque specs: Fuel rail bolts: typically 8–12 Nm — verify spec.

Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →