Diagnose soonCould result in catastrophic engine damage; severe. Do not drive until diagnosed.
There is not enough oil pressure to run the high-pressure fuel injection system - on diesels this points to low oil, oil pump, or engine timing problems.
Model notes: Seen on 2003 Ford 6.0L F-250 (died on freeway, hard start). Applies to Ford, Range Rover, BMW, Peugeot.
Key facts
P2290 means injector Control Pressure Too Low. There is not enough oil pressure to run the high-pressure fuel injection system - on diesels this points to low oil, oil pump, or engine timing problems. WrenchFair's published fair-price range for this repair is $50–$600 parts and $150–$800 labor at independent shops.
WrenchFair rates P2290 a 5-of-5 DIY difficulty (“Diesel high-pressure injection and oil pressure diagnosis requires gauges, factory data, and experience.”) with a “Diagnose soon” driveability rating: Could result in catastrophic engine damage; severe. Do not drive until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2011–2016 Chevrolet Silverado HD (6.6L LML Duramax V8 diesel) — Bosch CP4.2 high-pressure fuel pump failure ('CP4 grenade'):Owner-verified
No factory recall for the pump itself on GM trucks (unlike Ford's 6.7L CP4.2 recall). Check your VIN at nhtsa.gov/recalls; the class-action settlement is the only factory-backed relief.
Do this test first: Research technical service bulletins for the specific vehicle first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2290 on the 2011–2016 Chevrolet Silverado HD — but the community-sourced Bosch CP4.2 high-pressure fuel pump failure ('CP4 grenade') note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
CP4.2 replacement / CP3 conversion fasteners: verify — A failed-pump repair is typically a shop job; use factory service torque values, not guesses.
Tips
The 2011-2016 LML is the only Duramax generation that shipped with the Bosch CP4.2 injection pump, and it is the engine's defining weak spot. Unlike the older CP3 it replaced, the CP4.2 is extremely sensitive to fuel lubricity: dirty fuel or water wears the internals, metal shavings start circulating, and the pump can destroy itself - and the whole high-pressure fuel system - in minutes, often with little warning.
Early warnings: long cranking, loss of power under load, rough idle, misfires, stalling that won't restart, and codes P0087, P0088, P0093, or P2290. If you find glitter in the fuel filter or water separator, the failure chain has already started - don't keep driving it.
GM's repair scope for a grenaded pump is the entire high-pressure side: pump, fuel rails, all eight injectors, high-pressure lines, return lines, plus cleaning the tank, sending unit, and chassis lines. Paid out of pocket at a dealer this routinely tops $10,000. A federal class action over these pumps reached a $50M final settlement in 2025 covering 2011-2016 Silverado/Sierra HD LML trucks (GM denies the defect); check the settlement terms if you already paid for a repair.
The owner-verified prevention playbook, repeated across DuramaxForum's LML section for years: convert to a CP3 pump before the CP4.2 fails, add a lift pump with real filtration, and change the fuel filter on schedule. A CP3 conversion costs a fraction of a post-failure repair.
2017 and newer trucks are not affected - GM switched the L5P Duramax to a Denso HP4 pump.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
no start condition
excessive smoke from the exhaust
peculiar noises from engine compartment
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Defective high-pressure injection pressure switch 2 owner notes link this repair to P2290
Open or shorted control circuits
Low oil level
Low oil pressure 2 owner notes link this repair to P2290
Owner notes linked to P2290: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research technical service bulletins for the specific vehicle first.
Make sure the engine is filled to the appropriate oil level and no oil pressure or oil level lamps are illuminated; if they are, perform a manual oil pressure test. Tests: Defective high-pressure injection pressure switch
Retrieve all stored codes and freeze frame data, record them, then clear codes and test-drive until the code restores or the PCM enters readiness mode.
Visually inspect related wiring and connectors; repair or replace wiring that has been cut, burned, or damaged.
Use the DVOM to test voltage and ground circuits at the injection system pressure sensor; check system fuses if no voltage.
If voltage is present, test the corresponding circuit at the PCM connector; an open circuit between the sensor and PCM is suspect if absent there.
Test the injection pressure sensor with the DVOM against manufacturer specifications; replace if non-compliant.
Note: although listed for some gasoline applications, this code is seen almost exclusively in diesel applications with an engine timing and/or lubrication issue.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2011–2016 Chevrolet Silverado HD: Bosch CP4.2 high-pressure fuel pump failure ('CP4 grenade') — test first, then buy for this job.
The price range below is a national planning range for P2290 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$50 – $600
Labor$150 – $800
High-pressure injection pressure sensor replacement; oil pump or engine timing repairs cost more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2290 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Diesel high-pressure injection and oil pressure diagnosis requires gauges, factory data, and experience.
Pro tip: Relieve fuel pressure first (pull the pump fuse, run the engine until it stalls). Work cold, battery disconnected, extinguisher within reach — no power tools near open fuel.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →