Diagnose soonCan result in ABS deactivation and erratic transmission shifting. Address as quickly as possible.
The transmission output speed does not match the speed the wheels are turning.
Model notes: Typically applies to Jeep, Chrysler, Dodge, Chevy. Known issue on some Dodge and Chrysler vehicles (service bulletin #21-031-14).
Key facts
P215C means output Shaft Speed - Wheel Speed Correlation. The transmission output speed does not match the speed the wheels are turning. WrenchFair's published fair-price range for this repair is $30–$150 parts and $75–$300 labor at independent shops.
WrenchFair rates P215C a 4-of-5 DIY difficulty (“Oscilloscope and DVOM testing of sensors and circuits is advanced; vehicle information specs are required.”) with a “Diagnose soon” driveability rating: Can result in ABS deactivation and erratic transmission shifting. Address as quickly as possible. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2014–2017 Jeep Cherokee (2.4L Tigershark I4, 3.2L Pentastar V6) — PTU failure / grinding noise:Owner-verified
The PTU sits between the transmission and the front axle on AWD models. Diagnosis is a dealer scan for the specific DTCs; replacement is a dealer or well-equipped independent job.
Do this test first: Check service bulletin #21-031-14 if the vehicle is a Dodge or Chrysler; it applies to this DTC.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P215C on the 2014–2017 Jeep Cherokee — but the community-sourced PTU failure / grinding noise note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
PTU replacement: verify — Torque specs not confirmed from a forum source — confirm against factory service info before torquing.
Tips
A grinding noise from under the vehicle, a MIL, and DTCs P1720 or P215C point to the PTU input spline failing on 2014–2017 AWD models — TSB 21-017-21 covers it with an updated part (68307403AG).
Check your VIN for coverage before paying anything: the PTU warranty was extended to 8 years / 150,000 miles on affected 2014–2017 Cherokees, and a 2020 recall covered ~95,000 2014–2017s for a related gear-teeth wear issue (power loss, may not shift into park) with a software remedy.
Out-of-pocket PTU replacement runs around $6,000 per owner reports — which is exactly why the VIN/coverage check comes first.
A separate recall issue: if the PTU fails catastrophically the vehicle may not be drivable to perform the recall diagnostic test, and owners report coverage fights in that scenario — document everything and push the dealer to run the test procedure.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
erratic speedometer
inadvertent ABS or traction control system (TCS) activation
irregular transmission shift patterns
ABS codes may be stored
the ABS may be disabled
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Excessive metallic debris on output/wheel speed sensor magnet
Defective output shaft/wheel speed sensor
Cut or damaged wiring or connectors
Broken, damaged, or worn reluctor ring teeth
Faulty PCM, ABCM, or EBCM
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 9 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check service bulletin #21-031-14 if the vehicle is a Dodge or Chrysler; it applies to this DTC.
Retrieve all stored codes and freeze frame data, write them down, clear the codes, and test-drive to see if P215C resets.
Perform a visual inspection of system-related wiring and connectors. Tests: Cut or damaged wiring or connectors
With an oscilloscope: connect the positive test lead to the sensor signal circuit and the negative lead to ground. With the drive wheels safely secured off the ground, run up the drivetrain and observe the waveform; look for an even pattern with no voltage spikes or glitches through all gears. Tests: Excessive metallic debris on output/wheel speed sensor magnet
With the DVOM on the ohms setting and the sensor unplugged, probe the sensor connector pins and compare with sensor testing specifications; sensors not complying with specs are faulty.
Test reference voltage at the sensor connector with KOEO and the sensor disconnected (usually 5 volts); check ground pin as well.
Reconnect the sensor and observe signal voltage while running up the driveline; use the vehicle speed-to-voltage chart to verify the sensor functions properly at a variety of speeds.
If the signal is good at the sensor connector but not at the controller connector, there is an open circuit between the controller and the sensor being tested.
Suspect controller failure or programming error only after exhausting all other possibilities.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2014–2017 Jeep Cherokee: PTU failure / grinding noise — test first, then buy for this job.
The price range below is a national planning range for P215C on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $150
Labor$75 – $300
Output shaft or wheel speed sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P215C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Oscilloscope and DVOM testing of sensors and circuits is advanced; vehicle information specs are required.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →