Diagnose soonThrottle faults can trigger limp mode with reduced power. Avoid highways until diagnosed.
The throttle is stuck shut and won't open when you press the gas. The engine is starved for air, so the car barely accelerates.
Model notes: Vehicles that idle extensively (delivery, security patrol) build throttle carbon fastest - periodic throttle cleaning prevents this code.
Key facts
P2112 means throttle actuator control system - stuck closed. The throttle is stuck shut and won't open when you press the gas. The engine is starved for air, so the car barely accelerates. WrenchFair's published fair-price range for this repair is $10–$250 parts and $80–$250 labor at independent shops.
WrenchFair rates P2112 a 2-of-5 DIY difficulty (“Carbon is the usual cause and cleaning is straightforward; motor failure means throttle body replacement.”) with a “Diagnose soon” driveability rating: Throttle faults can trigger limp mode with reduced power. Avoid highways until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2013–2020 Ford Fusion (2.5L Duratec I4, 1.5L EcoBoost I4, 1.6L EcoBoost I4, 2.0L EcoBoost I4, 2.7L EcoBoost V6) — Electronic throttle body failure — wrench light, limp mode (P2111/P2112):Factory-documented
The throttle body sits on top of the intake manifold at the front of the engine — fully accessible without removing anything else. Basic hand tools only; it seals with an O-ring (inspect and reuse if undamaged). Clear codes with any OBD-II scanner afterward.
Do this test first: Inspect the throttle bore - a carbon ring at the blade edge is the classic cause
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for p2112 on the 2013–2020 Ford Fusion — but the community-sourced Electronic throttle body failure — wrench light, limp mode (P2111/P2112) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
A sudden wrench light (powertrain malfunction indicator) with the car dropping into limp mode — capped around 1,000–2,000 RPM with no throttle response — is the classic electronic-throttle-body failure on 2013–2020 Fusions. Codes are usually P2111 (throttle stuck open) or P2112 (stuck closed), sometimes P2135. Restarting the car clears it temporarily until it happens again.
Ford TSB 16-0139 covers exactly this on 2015–2016 Fusions with the 2.0L and 2.5L (and TSB 10-21-6 covered the same failure on 2010–2011 cars): if the ETB wiring and connector check out and the throttle plate moves freely, the fix is replacing the electronic throttle body. Oil vapor gumming up the throttle plate is the usual root cause on higher-mileage cars.
This is one of the easiest DIY repairs on the car: disconnect the intake tube (flathead screwdriver on the clamp), unplug the wiring connector, remove the four 10mm bolts, swap the unit, reverse. Owners consistently report 10–15 minutes. Cleaning a gummed-up throttle body sometimes buys time, but a unit setting P2111/P2112 repeatedly needs replacement, not another cleaning.
After replacement some cars need an idle/throttle relearn — disconnecting the battery for 10+ minutes or driving through a few warm-up cycles usually settles it. Match the part number to your engine; the 2.5L and EcoBoost units differ.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “Owners consistently report 10–15 minutes.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
almost no power
engine barely revs
limited power mode
check engine light
engine will not start
smoke from tailpipe
increased fuel consumption
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Severe carbon buildup gluing the blade shut (most common)
Failed throttle actuator motor 2 owner notes link this repair to P2112
Damaged gears in the throttle body 2 owner notes link this repair to P2112
Electrical fault preventing motor operation 2 owner notes link this repair to P2112
Owner notes linked to P2112: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the throttle bore - a carbon ring at the blade edge is the classic cause Tests: Severe carbon buildup gluing the blade shut (most common)
Clean and verify the blade moves freely through its full range by hand (key off)
Command the throttle with a scan tool and confirm it follows commands Tests: Failed throttle actuator motor
Replace the assembly if the motor cannot move a clean, free blade
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2020 Ford Fusion: Electronic throttle body failure — wrench light, limp mode (P2111/P2112) — test first, then buy for this job.
The price range below is a national planning range for p2112 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$10 – $250
Labor$80 – $250
Cleaning is nearly free; throttle body replacement costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2112 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Carbon is the usual cause and cleaning is straightforward; motor failure means throttle body replacement.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →