Community-sourced DIY repair guides for the 2013–2020 Ford Fusion, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
The throttle body sits on top of the intake manifold at the front of the engine — fully accessible without removing anything else. Basic hand tools only; it seals with an O-ring (inspect and reuse if undamaged). Clear codes with any OBD-II scanner afterward.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “Owners consistently report 10–15 minutes.” — as written in the note. First-timers often take twice this.
Tips
A sudden wrench light (powertrain malfunction indicator) with the car dropping into limp mode — capped around 1,000–2,000 RPM with no throttle response — is the classic electronic-throttle-body failure on 2013–2020 Fusions. Codes are usually P2111 (throttle stuck open) or P2112 (stuck closed), sometimes P2135. Restarting the car clears it temporarily until it happens again.
Ford TSB 16-0139 covers exactly this on 2015–2016 Fusions with the 2.0L and 2.5L (and TSB 10-21-6 covered the same failure on 2010–2011 cars): if the ETB wiring and connector check out and the throttle plate moves freely, the fix is replacing the electronic throttle body. Oil vapor gumming up the throttle plate is the usual root cause on higher-mileage cars.
This is one of the easiest DIY repairs on the car: disconnect the intake tube (flathead screwdriver on the clamp), unplug the wiring connector, remove the four 10mm bolts, swap the unit, reverse. Owners consistently report 10–15 minutes. Cleaning a gummed-up throttle body sometimes buys time, but a unit setting P2111/P2112 repeatedly needs replacement, not another cleaning.
After replacement some cars need an idle/throttle relearn — disconnecting the battery for 10+ minutes or driving through a few warm-up cycles usually settles it. Match the part number to your engine; the 2.5L and EcoBoost units differ.
Everything happens at the fuel door — no tools needed for the funnel procedure. The funnel ships with the car in the spare-tire area; if yours is missing, any fuel filler funnel that fits the capless inlet works.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Tips
A “Check Fuel Fill Inlet” message on the cluster — sometimes followed by a check-engine light with P0456 or P0457 — is the capless Easy Fuel system's way of saying its spring-loaded filler flap isn't sealing. Dirt, ice, or a worn seal lets fuel vapor escape, which the EVAP monitor reads as a leak.
The owner's-manual fix works surprisingly often: pull over safely, engine off, open the fuel door, clear any visible debris, then insert the fuel funnel (stored with the spare tire) into the filler several times to dislodge grit and reseat the flap. It can take several drive cycles for the message to clear after the fix.
For a stubborn flap, owners report success cleaning the sealing area and applying a light silicone-safe lubricant, then working the flap open and closed a few times. Don't force anything down into the tank — and don't top off past the pump's first click, which floods the EVAP system and sets its own codes.
If the message keeps returning after cleaning, the filler-neck seal itself may be worn. That's a filler-neck replacement — still a driveway job (a few bolts and hose clamps) — but get a smoke test confirming the leak location before buying parts.
Blend door actuator clicking behind the dash (stripped gears) Owner-verified(All engines)
The glove box drops out by squeezing its side tabs — no tools needed for access. You'll need a 7mm socket, a Phillips bit, and trim tools. Set the HVAC to full cold before removing the old actuator so the new one indexes correctly.
Typical difficulty: Easy — based on 16 code guides for the ac repair area (an area-level estimate, not this exact job).
Tips
Clicking or rapid tapping from behind the dash when you change the temperature setting — sometimes with one side blowing hot and the other cold on dual-zone cars — is a stripped blend-door actuator gear. It's one of the most-reported HVAC complaints on 2013–2020 Fusions.
Diagnosis is easy: sit in the car, key on (engine off is fine), and sweep the temperature knob from full cold to full hot while listening. A failing actuator clicks audibly right behind the glove box (passenger/right side) or under the driver's side of the center stack, depending on which actuator failed.
The passenger-side actuator is a genuine DIY job: remove the glove box, unplug the actuator, remove its screws (7mm/Phillips), and swap it — video walkthroughs cover 2013–2020 specifically. The driver's-side unit is tighter (some owners remove the brake-pedal connecting pin for access) but still doable without pulling the dash.
Rule out low refrigerant first if the symptom is uneven temperatures rather than clicking: one owner thread found the actuator fine and the real problem was a low refrigerant charge. Clicking = actuator; no clicking + warm air = check the refrigerant charge.
Battery replacement — the BMS reset you must not skip Owner-verified(All engines)
The battery is in the engine bay (driver's side). FORScan plus an inexpensive ELM327-compatible adapter handles the reset at home. The 8-hour locked-car method costs nothing but patience.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Tips
After replacing the 12V battery on a 2013–2020 Fusion, the Battery Management System (BMS) must be told there's a new battery — otherwise the car keeps charging to the old, worn battery's profile. Symptoms of a skipped reset: auto start/stop stops working, odd battery/charging warnings, and a shortened life for the new battery.
Three ways to reset it: (1) a dealer or shop scan tool, (2) FORScan software with an OBD-II adapter (the DIY favorite — it has a dedicated BMS reset function), or (3) the no-tool method owners confirm works: leave the car locked and completely untouched for 8+ hours (no key fob near it, no Ford app open) so the BMS self-calibrates.
There's also a manual button sequence from Ford service literature: ignition on, engine off, then within 10 seconds press the rear-fog button 5 times and the hazard button 3 times (cars with a rear fog button) — or flash the high beams 5 times and press the brake pedal 3 times (cars without). The charging-system telltale blinks 3 times to confirm. FORScan is the surest bet if the sequence doesn't take on your model year.
The owner's manual also warns: never connect accessory grounds directly to the battery negative post — it bypasses the BMS current sensor and corrupts its measurements. Ground to chassis instead.
Rear brake pads — EPB service (maintenance) mode is mandatory Owner-verified(All engines)
Rear calipers are accessible with the wheel off — no lift required, jack stands are fine. You need a caliper compressor (not a wind-back tool), basic sockets, and either the manual pedal/switch sequence or an EPB-capable scan tool.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Tips
2013–2020 Fusions with the electronic parking brake punish the old-school brake job: if you just wind the rear caliper piston back without putting the EPB in service (maintenance) mode first, you can damage or desynchronize the caliper motors. Owners report a dead EPB, warning lights, and in the worst case a caliper replacement after what should have been a pad slap.
The no-scan-tool procedure straight from the workshop manual — activation: ignition ON, press and hold the accelerator pedal AND hold the EPB switch in RELEASE (down), then cycle ignition OFF→ON within 5 seconds while still holding both. The yellow EPB light comes on and the cluster shows Maintenance Mode. Do the brake job, then deactivate: ignition ON, hold accelerator + EPB switch in APPLY (up), cycle OFF→ON within 5 seconds.
In service mode the rear piston pushes straight back in — do NOT rotate it like an old screw-type caliper. A basic caliper compressor or C-clamp works. Rotating the piston with the motor still engaged is exactly what kills the actuator.
If you already skipped the procedure and the EPB is throwing faults, run the activation/deactivation cycle first — it recalibrates the motors. If a motor is truly damaged (stripped gears from forced rotation), the caliper/motor assembly needs replacement. A FORScan or EPB-capable scan tool can also enter service mode and is the easier route if you own one.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 1,888 complaints for the 2013–2020 Ford Fusion. 2016 was the worst year (1705 complaints). Most-reported areas: engine, power train, unknown or other.
19V632000 (29/08/2019) — STEERING:ELECTRIC POWER ASSIST SYSTEM Ford Motor Company (Ford) is recalling certain 2013-2016 Ford Fusion and Lincoln MKZ, 2015-2016 Ford Edge, and 2016 Lincoln MKX vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan…
25V442000 (27/06/2025) — BACK OVER PREVENTION:SOFTWARE Ford Motor Company (Ford) is recalling certain 2018-2022 Transit Connect, 2019-2020 MKZ, MKX, Edge, Continental, F-150, Nautilus, Fusion, 2019-2023 Ranger, Mustang, 2020-2021 EcoSport, Expedition, Navigator, 2020-2022 Escape, F-250 SD, Corsair, 2020-2023 Aviator, Transit, 2020-2024 Explorer, 2021-2024 Bronco Sport, and 2022-2024…
16V250000 (27/04/2016) — SEAT BELTS:FRONT:ANCHORAGE Ford Motor Company (Ford) is recalling certain model year 2016 Ford Fusion vehicles manufactured from March 10, 2016, through March 16, 2016. The front driver seat track assembly's rear riser may have been improperly welded to the seat track rail…
23V440000 (23/06/2023) — ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY:MANAGEMENT SYSTEM/ENERGY CONTROL MODULE (BMS/BECM) Ford Motor Company (Ford) is recalling certain 2019-2020 Fusion PHEV vehicles. The battery energy control module (BECM) may become damaged due to excessive voltage and current flow.
20V177000 (23/03/2020) — LATCHES/LOCKS/LINKAGES:DOORS:LATCH Ford Motor Company (Ford) is recalling certain 2014-2015 Fiesta, 2014-2016 Fusion and Lincoln MKZ vehicles sold, or ever registered in Alabama, Arkansas, Arizona, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, New Mexico, Nevada, Oklahoma, Oregon, South Carolina, Texas, Utah, Washington, Puerto…
23V775000 (17/11/2023) — LATCHES/LOCKS/LINKAGES:DOORS:LATCH Ford Motor Company (Ford) is recalling certain 2015 Fiesta, 2016 Fusion, and 2016 Lincoln MKZ vehicles sold, or ever registered in Alabama, Arkansas, Arizona, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, New Mexico, Nevada, Oklahoma, Oregon, South Carolina, Texas, Utah, Washington…
16 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2013–2020 Ford Fusion yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.