Diagnose soonExpect reduced power or limp mode — the hybrid system protects itself by limiting the electric side. Drive gently to a shop and skip long trips.
This small electric pump moves transmission fluid around; on hybrids it keeps the transaxle lubricated and cool. This code means the computer saw an electrical problem in the wiring in the pump's motor. It's a low-voltage part, but it lives near high-voltage hardware, so keep your hands and tools clear of any orange cables.
Key facts
P0C2B means electric/auxiliary transmission fluid pump control module feedback signal. This small electric pump moves transmission fluid around; on hybrids it keeps the transaxle lubricated and cool. This code means the computer saw an electrical problem in the wiring in the pump's motor. It's a low-voltage part, but it lives near high-voltage hardware, so keep your hands and tools clear of any orange cables. WrenchFair's published fair-price range for this repair is $75–$700 parts and $150–$600 labor at independent shops.
WrenchFair rates P0C2B a 3-of-5 DIY difficulty (“Middle of the road: visual checks, connectors, fuses, and 12V tests are DIY-friendly, but anything on the high-voltage side belongs to a technician.”) with a “Diagnose soon” driveability rating: Expect reduced power or limp mode — the hybrid system protects itself by limiting the electric side. Drive gently to a shop and skip long trips. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2009 GMC Yukon Hybrid (6.0L V8) — Aux pump control module (bump/jerk + autostop stall):Factory-documented
The control module lives under the 12V battery in the front of the engine bay. A DIY-capable owner can swap the module and harnesses in under two hours, but the harness work is fiddly pigtail splicing, not plug-and-play.
Do this test first: Power the car fully off, then treat every orange cable and the battery pack as lethal — high voltage can kill. Only qualified technicians open the pack or service HV parts; your DIY stops at 12V checks, fuses, and connectors you can reach without opening anything.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0C2B on the 2008–2009 GMC Yukon Hybrid — but the community-sourced Aux pump control module (bump/jerk + autostop stall) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Aux pump control module and harness fasteners: verify — Torque specs for the module and harness fasteners not confirmed from a forum source — confirm against factory service info before torquing.
Tips
Know the pattern: the truck stalls or shuts off coming out of Auto Stop, sometimes with a bump or jerk as it switches between electric and engine modes. Codes P0AC4 (hybrid powertrain requested MIL), P2797 (aux pump performance), P0C2B (pump module feedback), and P0AB9 (autostop failed to restart) point at the aux pump circuit, not at the whole transmission.
Follow the owner-proven fix: replace the hybrid transmission (aux pump) control module plus the two harnesses. GM part 24261817 is the updated module; order connector pigtails 24259589 and 24259590 for 2008-2009 trucks. A 2008 Yukon owner did it himself in under two hours for about $500 in parts (another owner's parts quote was $292 shipped) and confirmed no stalls for more than a year afterward; a second 2008 Yukon owner replaced the module and wiring and eliminated the bump/jerk.
Heed the DIY warning from that owner: the harnesses are pigtail-only and are NOT a wire-for-wire swap — build the connections carefully per the bulletin. The truck needs a few days to relearn the new module and will not enter auto stop during the relearn.
Back it with GM's own preliminary information (NHTSA MC-10154554-9999), which names the module-and-harness swap as the first resolution for the bump/jerk symptom. If the module does not fix it, the next step is the aux pump itself (about $1,200), not a transmission rebuild.
Keep the differential in mind: one owner found P0AC4 can also indicate a dying hybrid pack — but the documented module fix held for over a year, so check the pack's cell-voltage spread before condemning it.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine or transmission warning light on
harsh, delayed, or missing shifts
possible limp mode (locked in one gear)
slipping or shuddering during gear changes
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
feedback signal failed
wiring fault
failed auxiliary pump motor 2 owner notes link this repair to P0C2B
Owner notes linked to P0C2B: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Power the car fully off, then treat every orange cable and the battery pack as lethal — high voltage can kill. Only qualified technicians open the pack or service HV parts; your DIY stops at 12V checks, fuses, and connectors you can reach without opening anything.
Check the transmission fluid level and condition per the owner's manual.
With the car powered on, listen for the pump running.
Check the pump's fuse and electrical connector.
Pump replacement is usually straightforward but often buried — get a quote if access looks bad.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2009 GMC Yukon Hybrid: Aux pump control module (bump/jerk + autostop stall) — test first, then buy for this job.
The price range below is a national planning range for P0C2B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$75 – $700
Labor$150 – $600
feedback signal failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0C2B ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Middle of the road: visual checks, connectors, fuses, and 12V tests are DIY-friendly, but anything on the high-voltage side belongs to a technician.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →