P0C2B

P0C2B on a 2008–2009 GMC Yukon Hybrid: Electric/auxiliary transmission fluid pump control module feedback signal

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0C2B on a 2008–2009 Chevrolet Tahoe Hybrid · 2008–2009 GMC Yukon Hybrid

DIY difficulty 3/5

This small electric pump moves transmission fluid around; on hybrids it keeps the transaxle lubricated and cool. This code means the computer saw an electrical problem in the wiring in the pump's motor. It's a low-voltage part, but it lives near high-voltage hardware, so keep your hands and tools clear of any orange cables.

Key facts

☑ Before you buy parts — check these first:
On your 2008–2009 GMC Yukon Hybrid (6.0L V8) — Aux pump control module (bump/jerk + autostop stall): Factory-documented
The control module lives under the 12V battery in the front of the engine bay. A DIY-capable owner can swap the module and harnesses in under two hours, but the harness work is fiddly pigtail splicing, not plug-and-play.
Do this test first: Power the car fully off, then treat every orange cable and the battery pack as lethal — high voltage can kill. Only qualified technicians open the pack or service HV parts; your DIY stops at 12V checks, fuses, and connectors you can reach without opening anything.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0C2B on the 2008–2009 GMC Yukon Hybrid — but the community-sourced Aux pump control module (bump/jerk + autostop stall) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: owner forum · owner forum · GM PIP / NHTSA TSB PDF

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0C2B: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Power the car fully off, then treat every orange cable and the battery pack as lethal — high voltage can kill. Only qualified technicians open the pack or service HV parts; your DIY stops at 12V checks, fuses, and connectors you can reach without opening anything.
  2. Check the transmission fluid level and condition per the owner's manual.
  3. With the car powered on, listen for the pump running.
  4. Check the pump's fuse and electrical connector.
  5. Pump replacement is usually straightforward but often buried — get a quote if access looks bad.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2008–2009 GMC Yukon Hybrid: Aux pump control module (bump/jerk + autostop stall) — test first, then buy for this job.
The price range below is a national planning range for P0C2B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$75 – $700
Labor$150 – $600

feedback signal failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0C2B ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Middle of the road: visual checks, connectors, fuses, and 12V tests are DIY-friendly, but anything on the high-voltage side belongs to a technician.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →