Diagnose soonSlipping generates heat and wear fast - diagnose promptly, drive gently.
Your transmission is slipping in gear 1 - the computer measured the wrong ratio. Check the fluid level and condition first; low or burnt fluid is the most common cause. If the fluid is fine, it is internal wear.
Key facts
P0731 means gear 1 Incorrect Ratio. Your transmission is slipping in gear 1 - the computer measured the wrong ratio. Check the fluid level and condition first; low or burnt fluid is the most common cause. If the fluid is fine, it is internal wear. WrenchFair's published fair-price range for this repair is $100–$3500 parts and $200–$1500 labor at independent shops.
WrenchFair rates P0731 a 4-of-5 DIY difficulty (“Fluid check first; internal repair needs a transmission shop.”) with a “Diagnose soon” driveability rating: Slipping generates heat and wear fast - diagnose promptly, drive gently. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2022–2023 Ram 3500 (6.7L High Output Cummins Turbo Diesel) — Aisin K1 clutch snap ring failure (P0731):Owner-verified
Dealer-only warranty repair — the value is knowing the coverage exists and what to demand before paying for a transmission. The fix is replacing the K1 clutch drum assembly, not swapping the whole transmission.
Do this test first: Check the fluid level and condition - burnt smell or dark color is bad news.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0731 on the 2022–2023 Ram 3500 — but the community-sourced Aisin K1 clutch snap ring failure (P0731) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
K1 clutch drum assembly fasteners: verify — Torque spec not confirmed from a forum source — confirm against factory service info; this is a dealer warranty repair.
Tips
The failure signature is unmistakable: the truck loses forward gears 1 through 4, the malfunction indicator lamp comes on, and the TCM sets P0731-00 (Gear 1 Shift Incorrect Ratio). Fifth gear and reverse usually still work.
FCA extended the warranty on the Aisin K1 Clutch / Input Shaft Assembly to 10 years / 150,000 miles for certain 2022 trucks after NHTSA opened a probe (82 complaints, 16 of them complete loss of motive power above 25 mph). Owner reports include 2023 trucks, so check your VIN even if you own a 2023.
If you have already paid for this repair, the owner letter says you can submit the receipts for reimbursement through FCA's recall-reimbursement channel.
Stop driving the moment it fails. Owners tracking hundreds of these failures report that trucks driven on (low range, flooring it to get off the highway) are the ones that pick up collateral damage; the ones shut down immediately usually need only the K1 drum.
Dealers initially swapped whole transmissions, and several replacement transmissions failed the same way — the per-TSB fix is replacing the K1 clutch drum assembly, so push for that repair under the extended warranty rather than a full swap.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
slipping in gear 1
flaring shifts
limp mode
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
low transmission fluid
burnt/contaminated fluid
worn clutch pack 6 owner notes link this repair to P0731
faulty solenoid
valve body fault 6 owner notes link this repair to P0731
Owner notes linked to P0731: 6 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check the fluid level and condition - burnt smell or dark color is bad news. Tests: burnt/contaminated fluid
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Note which gears slip - one gear points to a clutch pack, all gears to pressure. Tests: worn clutch pack
Have a transmission shop test line pressure if the fluid is good. Tests: low transmission fluid
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2022–2023 Ram 3500: Aisin K1 clutch snap ring failure (P0731) — test first, then buy for this job.
The price range below is a national planning range for P0731 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $3500
Labor$200 – $1500
Fluid service or transmission rebuild per diagnosis. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0731 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Fluid check first; internal repair needs a transmission shop.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →