Diagnose soonDrivable; wrong temperature data shortens transmission life.
Your transmission changes how it shifts based on fluid temperature, and its temperature sensor is reading wrong - does not track actual temperature. That makes shifts harsh or sloppy. The sensor is often inside the transmission on the internal wiring harness.
Key facts
P0711 means transmission Fluid Temperature Sensor A Circuit Range/Performance. Your transmission changes how it shifts based on fluid temperature, and its temperature sensor is reading wrong - does not track actual temperature. That makes shifts harsh or sloppy. The sensor is often inside the transmission on the internal wiring harness. WrenchFair's published fair-price range for this repair is $50–$300 parts and $150–$400 labor at independent shops.
WrenchFair rates P0711 a 3-of-5 DIY difficulty (“The sensor is often inside the pan on the internal harness.”) with a “Diagnose soon” driveability rating: Drivable; wrong temperature data shortens transmission life. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2015–2016 Ram ProMaster City (2.4L Tigershark I4) — 9-speed 948TE: MIL, 'Unable To Engage Gear', limp mode — TCM reflash (TSB 21-018-17):Owner-verified
Dealer-only for the reflash (wiTECH or equivalent). A TCM hardware replacement has the module inside the transmission case — a shop job, owners report the dealer needed about three days and provided a loaner.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0711 on the 2015–2016 Ram ProMaster City — but the community-sourced 9-speed 948TE: MIL, 'Unable To Engage Gear', limp mode — TCM reflash (TSB 21-018-17) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
TCM software/hardware (dealer work): verify — Dealer-performed reflash and in-case module replacement; no owner torque spec published.
Tips
TSB 21-018-17 Rev B applies to 2015–2016 ProMaster City with the 9-speed 948TE (2.4L only): the fix is a dealer TCM software reflash, which also brings shift-quality improvements.
The bulletin covers a MIL with DTCs P0887, P1634, P1720, P1DCCD, P0711, P1DAD, or P1CC9 — one of which translates to the dash message 'Unable To Engage Gear.' Scan before authorizing any hardware work.
Owner repair records confirm the fix in the real world: one van went into limp mode (transmission 'holding back') at about 27,000 miles and was cured by the dealer flashing the transmission control module; another needed the TCM itself replaced and reported shifting 'improved by 100%' with faster, smoother acceleration.
The TCM sits inside the transmission case, so if the reflash does not cure it, the module replacement is a dealer/shop job — do not authorize a full transmission replacement for these codes first.
Do not confuse this software defect with the S24 recall (corroded CAN-C bus connector under the driver's seat causing unrequested neutral shifts) — different root cause, different fix; check for open recalls by VIN too.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh shifts when cold
slipping feel when hot
limp mode
check engine light on
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed temperature sensor
internal harness fault
wiring fault
corroded connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Watch the temperature reading - a stuck or jumpy value confirms it. Tests: failed temperature sensor
Compare with actual fluid temperature. Tests: failed temperature sensor
Inspect the internal harness. Tests: internal harness fault
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2015–2016 Ram ProMaster City: 9-speed 948TE: MIL, 'Unable To Engage Gear', limp mode — TCM reflash (TSB 21-018-17) — test first, then buy for this job.
The price range below is a national planning range for P0711 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$50 – $300
Labor$150 – $400
Transmission temperature sensor or internal harness replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0711 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is often inside the pan on the internal harness.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →