Community-sourced DIY repair guides for the 2015–2016 Ram ProMaster City, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
9-speed 948TE: MIL, 'Unable To Engage Gear', limp mode — TCM reflash (TSB 21-018-17) Owner-verified(2.4L Tigershark I4)
Dealer-only for the reflash (wiTECH or equivalent). A TCM hardware replacement has the module inside the transmission case — a shop job, owners report the dealer needed about three days and provided a loaner.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Torque specs
TCM software/hardware (dealer work): verify — Dealer-performed reflash and in-case module replacement; no owner torque spec published.
Tips
TSB 21-018-17 Rev B applies to 2015–2016 ProMaster City with the 9-speed 948TE (2.4L only): the fix is a dealer TCM software reflash, which also brings shift-quality improvements.
The bulletin covers a MIL with DTCs P0887, P1634, P1720, P1DCCD, P0711, P1DAD, or P1CC9 — one of which translates to the dash message 'Unable To Engage Gear.' Scan before authorizing any hardware work.
Owner repair records confirm the fix in the real world: one van went into limp mode (transmission 'holding back') at about 27,000 miles and was cured by the dealer flashing the transmission control module; another needed the TCM itself replaced and reported shifting 'improved by 100%' with faster, smoother acceleration.
The TCM sits inside the transmission case, so if the reflash does not cure it, the module replacement is a dealer/shop job — do not authorize a full transmission replacement for these codes first.
Do not confuse this software defect with the S24 recall (corroded CAN-C bus connector under the driver's seat causing unrequested neutral shifts) — different root cause, different fix; check for open recalls by VIN too.
Transmission shifts to/stays in neutral after a stop — corroded CAN-C bus connector (recall S24) Factory-documented(2.4L Tigershark I4)
Dealer-performed recall (inspection, connector replacement if corroded, relocation to under the instrument panel). No owner teardown.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Torque specs
CAN-C bus connector relocation (recall work): verify — Dealer-performed recall; no owner torque spec published.
Tips
On 2015–2016 ProMaster City vans (built Sept 26, 2014 through March 5, 2016), the low-voltage CAN-C bus communication connector sits by the front driver seat where it can take on water and corrode.
Corroded pins lose contact with the transmission control module, and the transmission can then unexpectedly shift into and stay in neutral the next time the van stops — with no warning. Shutting the engine off in that state can also cause a no-start.
The fix is recall S24 / NHTSA 16V-202: dealers inspect the connector, replace it if pins are corroded, and relocate it to a dry spot under the instrument panel — free of charge. The campaign began June 3, 2016.
This is a different defect from the S55 campaign (bad wire crimps on some 2015 Renegade/Cherokee/200 harnesses) and from the 21-018-17 TCM software issue — same symptom family (neutral shifts), different root cause. If your 2015–2016 City drops to neutral, check this campaign by VIN before paying for transmission diagnosis.
Used-buyer tip: a van this age should have the connector already relocated; if the connector is still under the driver's seat, the recall work was never done — get it done before a rainstorm does it for you.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 57 complaints for the 2015–2016 Ram ProMaster City. 2016 was the worst year (57 complaints). Most-reported areas: engine, electrical system, power train.
16E039000 (28/04/2016) — ELECTRICAL SYSTEM:SOFTWARE Chrysler (FCA US LLC) is recalling certain RAM ProMaster Trailer Light Modules, part number 68229650AB. These accessory modules were sold for installation on RAM ProMaster and ProMaster City vehicles. The Trailer Tow Lighting Control Module may have a software error…
16V253000 (28/04/2016) — ELECTRICAL SYSTEM:SOFTWARE Chrysler (FCA US LLC) is recalling certain model year 2014-2016 RAM ProMaster vehicles manufactured July 24, 2015, to February 15, 2016, and 2015-2016 ProMaster City vehicles manufactured August 15, 2014, to February 1, 2016. The Trailer Tow Lighting Control Module…
17V601000 (26/09/2017) — EQUIPMENT:OTHER:LABELS Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM ProMaster City vehicles. These vehicles have incorrect information on the tire placard including incorrect vehicle capacity weight, total number of occupants, tire pressure and/or "None" designation for the spare tire size…
17V824000 (21/12/2017) — EQUIPMENT Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the…
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2015–2016 Ram ProMaster City yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.