Diagnose soonDrivable if the car runs normally, but internal faults can strand you - diagnose soon.
Your car's computer constantly checks itself, and one of those self-checks failed (the fuel injector control module (diesel FICM) self-tests). This can mean the computer itself is bad - but low battery voltage or a botched software update causes the same code, so check those first. Replacing the computer means programming the new one.
Key facts
P0611 means fuel Injector Control Module Performance. Your car's computer constantly checks itself, and one of those self-checks failed (the fuel injector control module (diesel FICM) self-tests). This can mean the computer itself is bad - but low battery voltage or a botched software update causes the same code, so check those first. Replacing the computer means programming the new one. WrenchFair's published fair-price range for this repair is $200–$1200 parts and $150–$400 labor at independent shops.
WrenchFair rates P0611 a 4-of-5 DIY difficulty (“Module diagnosis needs a pro-level scan tool; replacement requires programming.”) with a “Diagnose soon” driveability rating: Drivable if the car runs normally, but internal faults can strand you - diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2001–2005 Chevrolet 2500 (6.6L Duramax V8 diesel (LB7/LLY)) — LB7/LLY FICM failure — crank/no-start and the 48-volt check:Owner-verified
Driveway diagnosis, mail-in repair — the FICM unbolts from the engine; board-level repair services test it in a real truck and return it plug-and-play.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0611 on the 2001–2005 Chevrolet 2500 — but the community-sourced LB7/LLY FICM failure — crank/no-start and the 48-volt check note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
The LB7/LLY Fuel Injection Control Module drives all eight injectors at 48 volts. When its power-supply board fails you get crank-but-no-start (especially cold), rough idle, misfires, stalling, or power loss under load. Watch FICM voltage on a scan tool: below 48V — often dropping to 30-40V — means the board is dying.
The code fingerprint is P0611 (FICM performance), U0105 (lost ECM/FICM communication), P0201-P0208 (injector circuits), P2146/P2149 (injector group voltage), and P1261/P1262 (internal FICM fault). A cluster of injector codes across BOTH banks points at the FICM, not eight bad injectors.
Do not confuse it with the LLY injector-harness chafe (covered in the Sierra HD platform-twin notes): harness failures hit specific cylinders with localized codes, while FICM failure is systemic — whole-bank codes, a voltage drop, and heat-related intermittents that come and go.
Board-level repair beats a junkyard FICM. Used units are the same age and fail the same way; repair services replace the known-weak components (not just the capacitors) and test in a real truck, and your repaired original needs no programming. Budget roughly $78 for bench diagnostics up to ~$750 for a full warranted repair.
Heat, moisture corrosion, and electrical abuse (jump starts, weak batteries) are what kill FICMs. Keep batteries healthy and connections clean — low system voltage makes the FICM work harder and die sooner.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
possible limp mode or no-start
multiple unrelated codes
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
low system voltage or weak battery
failed or interrupted software flash/update
bad power or ground to the control module
internal control module failure
water intrusion or corrosion at the module connector
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Check battery voltage and charging system - low voltage causes false internal-fault codes. Tests: low system voltage or weak battery
Check all powers and grounds at the control module connector. Tests: bad power or ground to the control module
Check for technical service bulletins - a software reflash may fix it. Tests: failed or interrupted software flash/update
If everything else passes, the module needs replacement and programming (usually a dealer or specialist).
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2001–2005 Chevrolet 2500: LB7/LLY FICM failure — crank/no-start and the 48-volt check — test first, then buy for this job.
The price range below is a national planning range for P0611 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$200 – $1200
Labor$150 – $400
Control module replacement and programming. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0611 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Module diagnosis needs a pro-level scan tool; replacement requires programming.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →