P0611

P0611 on a 2001–2005 Chevrolet 2500: Fuel Injector Control Module Performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0611 on a 2001–2005 Chevrolet 2500

DIY difficulty 4/5

Your car's computer constantly checks itself, and one of those self-checks failed (the fuel injector control module (diesel FICM) self-tests). This can mean the computer itself is bad - but low battery voltage or a botched software update causes the same code, so check those first. Replacing the computer means programming the new one.

Key facts

☑ Before you buy parts — check these first:
On your 2001–2005 Chevrolet 2500 (6.6L Duramax V8 diesel (LB7/LLY)) — LB7/LLY FICM failure — crank/no-start and the 48-volt check: Owner-verified
Driveway diagnosis, mail-in repair — the FICM unbolts from the engine; board-level repair services test it in a real truck and return it plug-and-play.
Do this test first: Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0611 on the 2001–2005 Chevrolet 2500 — but the community-sourced LB7/LLY FICM failure — crank/no-start and the 48-volt check note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Tips

Sources: 2001-2005 Duramax FICM failure signs and codes (module repair specialist) · Duramax LLY & LB7 FICM repair — symptoms and coverage (module repair specialist) · Common failure of the 2001-2004 LB7 FICM — symptoms and causes (module specialist blog)

Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
  2. Check battery voltage and charging system - low voltage causes false internal-fault codes. Tests: low system voltage or weak battery
  3. Check all powers and grounds at the control module connector. Tests: bad power or ground to the control module
  4. Check for technical service bulletins - a software reflash may fix it. Tests: failed or interrupted software flash/update
  5. If everything else passes, the module needs replacement and programming (usually a dealer or specialist).

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2001–2005 Chevrolet 2500: LB7/LLY FICM failure — crank/no-start and the 48-volt check — test first, then buy for this job.
The price range below is a national planning range for P0611 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$200 – $1200
Labor$150 – $400

Control module replacement and programming. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0611 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Module diagnosis needs a pro-level scan tool; replacement requires programming.

Watch this repair on YouTube

Parts & tools

Electrical diagnosis toolkit — what the job actually takes

Torque specs: Module connectors: hand-tight until they click — never force them.

Pro tip: Check powers AND grounds before condemning a module — most “module failures” are wiring. Disconnect the battery before unplugging modules.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →