Drive safeEmissions-related fault. Safe to drive; may affect fuel economy slightly.
The sensor reporting the exhaust valve's position is pegged high. The computer thinks the valve is wide open when it may not be.
Model notes: Corrosion bridging terminals inside the EGR connector is a known cause - inspect the connector closely before condemning the valve.
Key facts
P0406 means exhaust gas recirculation sensor A circuit high. The sensor reporting the exhaust valve's position is pegged high. The computer thinks the valve is wide open when it may not be. WrenchFair's published fair-price range for this repair is $80–$250 parts and $150–$350 labor at independent shops.
WrenchFair rates P0406 a 3-of-5 DIY difficulty (“High circuit usually means a short - inspect wiring before replacing the assembly.”) with a “Drive safe” driveability rating: Emissions-related fault. Safe to drive; may affect fuel economy slightly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Emissions warranty: P0406 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2008–2010 Chrysler Town & Country (3.3L V6, 3.8L V6) — EGR valve — P0404/P0406/P1404 codes:Owner-verified
From above on the 3.3L/3.8L: the EGR valve sits behind the alternator on the intake side. Several owners removed it with just a 1/4-inch drive and a flexible 10mm socket WITHOUT pulling the alternator — soak the bolts with penetrating oil a day ahead.
Do this test first: Unplug the sensor - persistent high reading means a harness short to voltage
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0406 on the 2008–2010 Chrysler Town & Country — but the community-sourced EGR valve — P0404/P0406/P1404 codes note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
EGR valve bolts: verify — Torque spec not confirmed from owner sources — confirm against factory service info for the 3.3L/3.8L before torquing; aluminum intake strips easily.
Tips
P0404/P0406/P1404 on the 3.3L/3.8L vans point at the EGR position sensor, which is integrated into the valve — the valve itself is the common failure item, confirmed by certified techs and many owner reports.
Try cleaning first: multiple owners cleared the code by removing the valve and cleaning it plus the tube with carb or throttle-body cleaner. If cleaning does not hold, replacement is about a 15-minute job and ~$75 for the part.
Check the electrical connector for loose or broken wires before buying the valve — a visual inspection costs nothing and a bad connector mimics a bad valve.
Use an OEM/dealer EGR valve if possible: one Chrysler tech reports repeated problems with aftermarket EGR valves on this engine.
For reference values if you have a scan tool: key-on-engine-off EGR position reads about 4.2 volts; at 35% duty cycle around 3.2 volts; at 50% around 2.2 volts.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
EGR control errors
failed emissions test
surging while driving
intermittent stalling
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Signal wire shorted to voltage (most common)
Failed position sensor with internal short
Open ground floating the signal high
Connector terminals bridged by corrosion
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Unplug the sensor - persistent high reading means a harness short to voltage Tests: Failed position sensor with internal short
Check the sensor ground carefully
Verify the sensor sweeps correctly off the vehicle if possible
Replace the assembly only after wiring is proven good
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2010 Chrysler Town & Country: EGR valve — P0404/P0406/P1404 codes — test first, then buy for this job.
The price range below is a national planning range for P0406 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$80 – $250
Labor$150 – $350
EGR valve replacement is typical. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0406 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — High circuit usually means a short - inspect wiring before replacing the assembly.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →