P0363

P0363: Misfire detected - fueling disabled

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0363?

Can I drive with a P0363 code?

No. The ECM already flagged this as catalyst-threatening - tow it if it's shaking badly. Have it towed rather than driven. (The only exception is moving the car a few feet to a safe spot, then shutting the engine off.)

How serious is P0363?

High. WrenchFair rates this one “Stop driving” — the most serious rating, reserved for faults that can strand you or cause real damage if you keep driving. The ECM already flagged this as catalyst-threatening - tow it if it's shaking badly.

Will P0363 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

The misfire got bad enough that the computer shut off fuel to the bad cylinder to save the catalytic converter. Fix the misfire first.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Read the companion misfire codes (P0301-P0312) Tests: Severe misfire from a failed ignition coil (most common)
  2. Diagnose the misfire on the identified cylinder Tests: Severe misfire from a failed ignition coil (most common)
  3. Repair the root cause
  4. Clear codes - fueling resumes automatically

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$40 – $150
Labor$50 – $150

Ignition coil and spark plug replacement for the misfiring cylinder. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0363 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Read the accompanying misfire codes to find the cylinder.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →