Diagnose soonThe car can stall without warning - avoid heavy traffic and get it fixed soon.
Can I drive with P0336?
Can I drive with a P0336 code?
Short trips and gentle driving only, until you know the cause. The car can stall without warning - avoid heavy traffic and get it fixed soon. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0336?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. The car can stall without warning - avoid heavy traffic and get it fixed soon.
Will P0336 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The sensor tracking crankshaft position is cutting out - typically when hot. Classic symptom: the car dies and won't restart until it cools down.
Model notes: On a high-mileage car, keep a spare crank sensor in the trunk - when it dies hot, you walk.
Key facts
P0336 means crankshaft position sensor A circuit range/performance. The sensor tracking crankshaft position is cutting out - typically when hot. Classic symptom: the car dies and won't restart until it cools down. WrenchFair's published fair-price range for this repair is $30–$100 parts and $80–$200 labor at independent shops.
WrenchFair rates P0336 a 2-of-5 DIY difficulty (“Access can be awkward but it is one bolt.”) with a “Diagnose soon” driveability rating: The car can stall without warning - avoid heavy traffic and get it fixed soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2020–2020 Buick Encore GX (1.2L I3 turbo (LIH)) — Blocked PCV passage — cam cover emission recall:Factory-documented
Dealer-only recall work: the dealer inspects the camshaft cover for the blockage and replaces the cover if it is restricted. No owner teardown needed.
Do this test first: Note whether failure is heat-related - the signature of a dying sensor
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0336 on the 2020–2020 Buick Encore GX — but the community-sourced Blocked PCV passage — cam cover emission recall note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Camshaft cover: verify — Dealer recall repair; no owner torque spec published in the sources — verify against factory service info if doing the work outside the recall.
Tips
Voluntary emission recall GM A202319910 targets 2020 Encore GX with the 1.2L LIH: the PCV passage inside the camshaft (cam) cover can be blocked from the factory, so crankcase pressure climbs until the engine runs rough — and the check-engine light comes on.
This is not a harmless light. A GM preliminary-information bulletin describes the failure chain: rising crankcase pressure balloons the rear main seal housing until the crankshaft reluctor makes contact with the crank sensor. That produces a crank-no-start or MIL with P0335/P0336.
If the reluctor has already cut through the rear main seal housing, metal contamination can force an engine replacement — so a 1.2L Encore GX that cranks but will not start, or throws crank-sensor codes, should go to the dealer promptly rather than sitting.
The dealer inspects the cam cover and replaces it if the passage is restricted, free under the recall. If your 2020 1.2L was never checked, ask the dealer to look up the field action on your VIN.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
stalling when hot
no start when hot
tach drops out
long crank
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failing crank sensor (heat-sensitive)
Damaged reluctor ring
Wiring chafed near hot exhaust
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Note whether failure is heat-related - the signature of a dying sensor Tests: Failing crank sensor (heat-sensitive)
Check the air gap and reluctor for damage Tests: Damaged reluctor ring
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2020–2020 Buick Encore GX: Blocked PCV passage — cam cover emission recall — test first, then buy for this job.
The price range below is a national planning range for P0336 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $100
Labor$80 – $200
One bolt and a connector, though access can be awkward. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0336 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Access can be awkward but it is one bolt.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →