Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonMisfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving.
The knock-listening sensor has gone deaf - it's sending no signal at all. The computer can't hear detonation, so it runs cautious low-power timing to stay safe.
VW/Audi note (VCDS): With the sensor unplugged, check for reference voltage at the ECM side of the connector to separate wiring faults from sensor faults.
Model notes: Low-input knock codes after engine work are frequently a forgotten connector - the knock sensor plug is small and easy to overlook during reassembly.
Key facts
P0327 means knock sensor 1 circuit low input, bank 1. The knock-listening sensor has gone deaf - it's sending no signal at all. The computer can't hear detonation, so it runs cautious low-power timing to stay safe. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0327 a 3-of-5 DIY difficulty (“Same access challenges as any knock sensor job; the low-input reading usually means open circuit.”) with a “Diagnose soon” driveability rating: Misfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
reduced performance
worse fuel economy
fluctuating rpm
hesitation
Likely causes
Failed knock sensor with no output (most common)
Open circuit in the sensor wiring
Corroded or loose connector dropping the tiny signal
Sensor not properly torqued to the block
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check connector and wiring for opens - low input almost always means the signal is not reaching the ECM Tests: Corroded or loose connector dropping the tiny signal
Measure sensor resistance; infinite resistance means a dead sensor
Verify mounting torque if the sensor was recently disturbed
Replace the sensor if wiring is intact Tests: Open circuit in the sensor wiring
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $120
Labor$80 – $180
Knock sensor or wiring repair is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0327 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Same access challenges as any knock sensor job; the low-input reading usually means open circuit.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →