P0327

P0327 on a 2000–2013 Chevrolet 2500: Knock sensor 1 circuit low input, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0327 on a 2000–2013 Chevrolet 2500

DIY difficulty 3/5

The knock-listening sensor has gone deaf - it's sending no signal at all. The computer can't hear detonation, so it runs cautious low-power timing to stay safe.

Model notes: Low-input knock codes after engine work are frequently a forgotten connector - the knock sensor plug is small and easy to overlook during reassembly.

Key facts

☑ Before you buy parts — check these first:
On your 2000–2013 Chevrolet 2500 (6.0L Vortec V8 (LQ4/LQ9/LY6/L96)) — 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix: Owner-verified
Driveway job with patience — both sensors live in the lifter valley UNDER the intake manifold, so the intake has to come off. Budget a half day the first time.
Do this test first: Check connector and wiring for opens - low input almost always means the signal is not reaching the ECM
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0327 on the 2000–2013 Chevrolet 2500 — but the community-sourced 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: P0327/P0332 knock sensor circuit-low diagnosis thread (owner forum) · Knock sensor location — 2004 Silverado 2500 6.0L under-intake confirmation (Q&A) · Knock sensor location — 2004 Silverado 6.0 under intake manifold (Q&A)

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check connector and wiring for opens - low input almost always means the signal is not reaching the ECM Tests: Corroded or loose connector dropping the tiny signal
  2. Measure sensor resistance; infinite resistance means a dead sensor
  3. Verify mounting torque if the sensor was recently disturbed
  4. Replace the sensor if wiring is intact Tests: Open circuit in the sensor wiring

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2000–2013 Chevrolet 2500: 6.0L Vortec knock sensors under the intake (P0327/P0332) — water intrusion, the TSB, and the RTV dam fix — test first, then buy for this job.
The price range below is a national planning range for P0327 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$30 – $120
Labor$80 – $180

Knock sensor or wiring repair is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0327 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Same access challenges as any knock sensor job; the low-input reading usually means open circuit.

Watch this repair on YouTube

Parts & tools

Spark plug & coil toolkit — what the job actually takes

Torque specs: Gasket-seat plugs: typically 20–30 Nm (15–22 lb-ft). Tapered-seat plugs: typically 11–18 Nm. Always verify against your engine’s factory spec — over-torquing strips aluminum threads.

Pro tip: Blow out the plug wells with compressed air BEFORE removing the plugs, so debris can’t fall into the cylinders.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →