Diagnose soonMisfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving.
The engine stumbles for the first few seconds after a cold start, then smooths out. The classic cause is a fuel injector that drips gasoline into a cylinder overnight.
Model notes: If the engine starts rough but smooths out within 30 seconds, suspect fuel leaking into cylinders overnight rather than ignition parts - ignition misfires usually persist when warm.
Key facts
P0316 means engine misfire detected on startup (first 1000 revolutions). The engine stumbles for the first few seconds after a cold start, then smooths out. The classic cause is a fuel injector that drips gasoline into a cylinder overnight. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$180 labor at independent shops.
WrenchFair rates P0316 a 3-of-5 DIY difficulty (“Overnight leak-down testing takes patience; the diagnosis spans fuel, ignition, and mechanical causes.”) with a “Diagnose soon” driveability rating: Misfires can damage the catalytic converter. Drive gently to a shop; if the check-engine light is flashing, stop driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 413 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Engine And Engine Cooling) — see the latest ones
On your 2011–2019 Ford Explorer (3.5L V6) — Spark plugs and ignition coils:Owner-verified
Transverse 3.5L V6 NA: the front 3 plugs/coils are directly accessible, but the rear bank sits under the upper intake plenum. Remove the air snorkel, disconnect the throttle body from the intake, then remove the plenum — 7 visible bolts plus one hidden bolt under the throttle body (easy to miss). Plan on a new intake plenum gasket for reassembly. Job takes roughly 2 hours, most of it hunting the hidden bolt. Front 3 = easy, rear 3 = the whole job.
Do this test first: Check which cylinders misfire on startup using misfire counters - one cylinder points at its injector or plug, random points at fuel pressure or battery
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0316 on the 2011–2019 Ford Explorer — but the community-sourced Spark plugs and ignition coils note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Spark plugs: 133 in-lbs (11 ft-lbs) — Gap 0.051 in (factory gap range 0.051–0.057 in per owner forum). Install on a cold engine; start plugs by hand to avoid cross-threading.
Intake plenum bolts: 89 in-lbs + 45-degree additional turn — Follow the factory torque sequence for the plenum; two-step torque-plus-angle.
Ignition coil bolts: verify — Confirm against factory service info for this vehicle.
Tips
Many replacement plugs (Motorcraft/NGK) have a silver anti-seize-style coating on the threads — do NOT add additional anti-seize, it will over-torque plugs in the aluminum heads.
Replace the intake plenum gasket when reassembling; reuse risks a vacuum leak.
The EcoBoost 3.5L (Sport) is different: owners report no intake removal is needed for its plugs — only the turbo charge pipe's bolt and clamps need to come off. This note covers the NA 3.5L.
Blow compressed air into each plug well before removing plugs so debris can't fall into the cylinder.
Common trigger: P0301–P0306 misfires where new plugs alone don't fix it — forum owners report the coil for the misfiring cylinder is often the real culprit.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Typical time: “Job takes roughly 2 hours, most of it hunting the hidden bolt.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
rough running for the first seconds after cold start
check engine light after cold starts
fuel smell on startup
symptoms clear as the engine warms
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears up)
Worn spark plugs with weak cold-start spark 3 owner notes link this repair to P0316
Carbon buildup on intake valves affecting cold mixture
Weak battery or slow cranking reducing cold-start spark energy 3 owner notes link this repair to P0316
Incorrect engine oil viscosity making cold cranking sluggish
Owner notes linked to P0316: 4 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check which cylinders misfire on startup using misfire counters - one cylinder points at its injector or plug, random points at fuel pressure or battery Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
Test fuel pressure leak-down overnight: pressure that bleeds off points at a leaking injector or check valve Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
Pull plugs on the offending cylinders after an overnight sit - wet plugs confirm injector leak-down Tests: Leaking fuel injector flooding a cylinder overnight (most common - starts rough, clears…
Load-test the battery - marginal batteries cause exactly this symptom on cold mornings Tests: Weak battery or slow cranking reducing cold-start spark energy
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2011–2019 Ford Explorer: Spark plugs and ignition coils — test first, then buy for this job.
Expensive fork: Fuel injector, then compression test — if the misfire stays on the same cylinder after a fresh plug and a swapped coil.
The price range below is a national planning range for P0316 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $180
Coils and spark plugs are the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0316 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Overnight leak-down testing takes patience; the diagnosis spans fuel, ignition, and mechanical causes.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →