Diagnose soonIf the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter.
Can I drive with P0304?
Can I drive with a P0304 code?
Short trips and gentle driving only, until you know the cause. If the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0304?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. If the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter.
Will P0304 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Cylinder 4 is misfiring - a bad coil, worn plug, or weak injector is the usual cause. A flashing check engine light means stop driving.
Key facts
P0304 means cylinder 4 misfire detected. Cylinder 4 is misfiring - a bad coil, worn plug, or weak injector is the usual cause. A flashing check engine light means stop driving. WrenchFair's published fair-price range for this repair is $40–$150 parts and $50–$150 labor at independent shops.
WrenchFair rates P0304 a 2-of-5 DIY difficulty (“Swap the coil with another cylinder first.”) with a “Diagnose soon” driveability rating: If the check engine light is flashing, stop driving - raw fuel is cooking the catalytic converter. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 374 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2010–2012 Subaru Outback (2.5L EJ253 SOHC) — Head gasket replacement:Owner-verified
Pull the engine — forum consensus is the EJ25 drops out in 1–2 hours, while in-car head work means fighting the frame rails for head-bolt access, a sore back, and no room to clean or straight-edge the deck. Engine-out also lets you reseal the oil pump, swap the plastic oil-separator plate for the updated metal one, and inspect the heads on a stand. Year note: Outbacks ran the EJ253 SOHC through 2012; 2013 switched to the FB25 (timing chain).
Do this test first: Swap the cylinder 4 coil with another cylinder
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0304 on the 2010–2012 Subaru Outback — but the community-sourced Head gasket replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Head bolts — FSM multi-stage torque-plus-angle (SOHC EJ25): Oil threads and washers. In sequence: 22 ft-lb, then 51 ft-lb; back off all bolts 180°, then another 180°; bolts 1&2 (center pair) to 25 ft-lb; bolts 3–6 (outer four) to 11 ft-lb; tighten all 80–90° in sequence, then a further 80–90° (total re-tightening angle must not exceed 180°). Tightening order from front of vehicle: top row 3-1-6, bottom row 5-2-4. Bolt 1 = middle top, 2 = middle bottom, 3 = left top, 4 = right bottom, 5 = left bottom, 6 = right top. — Quoted from the Subaru factory service manual on UltimateSubaru; AllData lists a slightly different revision for some model years — confirm against the FSM for your exact year before final assembly.
Valve cover bolts: 5 ft-lb — From the legacygt.com EJ engine removal write-up.
Intake manifold bolts: 18 ft-lb — From the legacygt.com EJ engine removal write-up.
Camshaft sprocket / cam bolt torque: verify — Confirm against the Subaru factory service manual for the exact engine revision.
Tips
Use MLS (multi-layer steel) gaskets only: OEM turbo MLS 11044AA770 or NA MLS 11044AA642, Fel-Pro PermaTorque MLS 26415PT (their documented fix for the 1999–2009 SOHC composite-gasket weakness), or Six Star — avoid the single-layer composite gasket dealers often supply by default (e.g. 11044AA633).
Why they fail: the SOHC EJ253 shipped with single-layer coated composite gaskets that develop external coolant and oil leaks at the head/block seam; the open-deck block and head flex chew through them over time.
Check head and deck flatness and resurface as needed — EJ heads warp easily after an overheat, and a light abrasive cleanup is not a substitute for a machine-shop check.
Follow the FSM torque-plus-angle sequence exactly: oil bolt threads and washers, blow out the bolt holes with compressed air, and never exceed 90° on a single angle step.
While the engine is out: reseal the oil pump with Ultra Grey/anaerobic, replace a plastic oil-separator plate with the updated metal one, and replace cam seals and valve-cover gaskets.
Do not keep driving or repeatedly overheat the engine while diagnosing — a badly warped deck or dropped liner turns a gasket job into a head/block replacement.
Typical time: “Pull the engine — forum consensus is the EJ25 drops out in 1–2 hours, while in-car head work means fighting the frame rails for head-bolt access, a sore back, and no room to clean or straight-edge the deck.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light (may flash)
rough idle
hesitation
loss of power
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed ignition coil on cylinder 4 (most common) 40 owner notes link this repair to P0304
Worn or fouled spark plug 40 owner notes link this repair to P0304
Clogged fuel injector 3 owner notes link this repair to P0304
Low compression on cylinder 4 8 owner notes link this repair to P0304
Owner notes linked to P0304: 54 across 4 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Swap the cylinder 4 coil with another cylinder Tests: Failed ignition coil on cylinder 4 (most common)
Inspect the spark plug Tests: Worn or fouled spark plug
Check compression on cylinder 4 Tests: Low compression on cylinder 4
Test the fuel injector Tests: Clogged fuel injector
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2010–2012 Subaru Outback: Head gasket replacement — test first, then buy for this job.
Expensive fork: Fuel injector, then compression test — if the misfire stays on the same cylinder after swapping the coil and plug — not a second set of coils.
The price range below is a national planning range for P0304 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $150
Labor$50 – $150
Ignition coil and spark plug replacement (cylinder 4). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0304 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Swap the coil with another cylinder first.
🔌 Read your spark plugs This code names the unhappy system; your plugs show what the combustion actually looks like. Pull one and match it to the visual chart — how to read your spark plugs →
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →