Your second airflow sensor is reading outside the believable range - usually dirty or there's an intake leak on its side.
Key facts
P010B means mAF sensor 'B' circuit range/performance. Your second airflow sensor is reading outside the believable range - usually dirty or there's an intake leak on its side. WrenchFair's published fair-price range for this repair is $60–$250 parts and $80–$200 labor at independent shops.
WrenchFair rates P010B a 2-of-5 DIY difficulty (“Clean the sensor first; compare against the 'A' sensor.”) with a “Diagnose soon” driveability rating: Fueling is off - address it soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2017–2022 Infiniti Q60 (3.0L VR30DDTT twin-turbo V6) — P0101 / P010B MIL: leaking or poorly connected air intake ducts (check before replacing MAF sensors):Owner-verified
DIY-friendly diagnosis note: the TSB's first step is a hands-on duct inspection - reseat and reclamp before buying sensors. Only buy parts after the ducts check out, and handle the MAF elements per the TSB's cautions.
Do this test first: Clean the 'B' MAF sensor with dedicated cleaner
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P010B on the 2017–2022 Infiniti Q60 — but the community-sourced P0101 / P010B MIL: leaking or poorly connected air intake ducts (check before replacing MAF sensors) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
On the VR30, P0101 and P010B are bank-specific duct codes: P0101 means the passenger (RH) side air duct, P010B the driver (LH) side. Start at the ducts, not the sensors.
The TSB's fix is mechanical, not electronic: inspect the applicable duct for leaks or poor connections, disconnect/remove it, then correctly reconnect and reinstall it so there are no leaks. A duct that was disturbed during other work (air filter change, turbo-area service) is the classic cause.
If you do handle the MAF sensors: never shock them, never disassemble them, never touch the sensor element, and only remove the sensor from the air cleaner cover if you must.
An earlier related bulletin (ITB17-017, 2017) covered P0101/P010B/P0106 with an ECM reprogram on 2017 cars - if the ducts check out on a 2017, ask the dealer whether the ECM software is current before buying parts.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
rough idle
hesitation
poor fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Contaminated 'B' MAF sensor (most common) 2 owner notes link this repair to P010B
Intake leak on the 'B' path 2 owner notes link this repair to P010B
Drifting/failing 'B' MAF sensor 2 owner notes link this repair to P010B
Owner notes linked to P010B: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Clean the 'B' MAF sensor with dedicated cleaner
Compare 'A' and 'B' readings - they should track together
Smoke-test the 'B' intake path for leaks Tests: Intake leak on the 'B' path
Replace the 'B' sensor if it still reads wrong when clean
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2017–2022 Infiniti Q60: P0101 / P010B MIL: leaking or poorly connected air intake ducts (check before replacing MAF sensors) — test first, then buy for this job.
The price range below is a national planning range for P010B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $250
Labor$80 – $200
MAF sensor 'B' cleaning or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P010B ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Clean the sensor first; compare against the 'A' sensor.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →