Your second airflow sensor is reading outside the believable range - usually dirty or there's an intake leak on its side.
Key facts
P010B means mAF sensor 'B' circuit range/performance. Your second airflow sensor is reading outside the believable range - usually dirty or there's an intake leak on its side. WrenchFair's published fair-price range for this repair is $60–$250 parts and $80–$200 labor at independent shops.
WrenchFair rates P010B a 2-of-5 DIY difficulty (“Clean the sensor first; compare against the 'A' sensor.”) with a “Diagnose soon” driveability rating: Fueling is off - address it soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2016–2023 Infiniti Q50 (3.0L VR30DDTT twin-turbo V6) — P0101/P010B: MIL on from loose or leaking air ducts (Infiniti bulletin ITB23-001):Owner-verified
Underhood inspection: remove the air cleaner case and air ducts, check for leaks and poor connections, then reinstall correctly. Do not disassemble or touch the MAF sensor element - the bulletin warns against shocking, disassembling, or touching it.
Do this test first: Clean the 'B' MAF sensor with dedicated cleaner
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P010B on the 2016–2023 Infiniti Q50 — but the community-sourced P0101/P010B: MIL on from loose or leaking air ducts (Infiniti bulletin ITB23-001) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
P0101 means inspect the passenger (RH) side air duct; P010B means the driver (LH) side. The bulletin's fix is the duct connection at the air cleaner case, not the MAF sensor itself.
Do not throw a MAF sensor at this code first - the bulletin procedure is to remove the air ducts as needed, inspect for leaks or poor connections, and reinstall them correctly.
If you do handle the air cleaner cover, the bulletin warns: never shock the MAF sensor, never disassemble it, never touch the sensor element - and only remove it from the cover if necessary.
For 2016-2019 models the bulletin points at the ESM section ENGINE > ENGINE MECHANICAL > VR30DDTT > REMOVAL AND INSTALLATION > AIR CLEANER AND AIR DUCT for the procedure.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
rough idle
hesitation
poor fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Contaminated 'B' MAF sensor (most common) 2 owner notes link this repair to P010B
Intake leak on the 'B' path 2 owner notes link this repair to P010B
Drifting/failing 'B' MAF sensor 2 owner notes link this repair to P010B
Owner notes linked to P010B: 2 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Clean the 'B' MAF sensor with dedicated cleaner
Compare 'A' and 'B' readings - they should track together
Smoke-test the 'B' intake path for leaks Tests: Intake leak on the 'B' path
Replace the 'B' sensor if it still reads wrong when clean
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2016–2023 Infiniti Q50: P0101/P010B: MIL on from loose or leaking air ducts (Infiniti bulletin ITB23-001) — test first, then buy for this job.
The price range below is a national planning range for P010B on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$60 – $250
Labor$80 – $200
MAF sensor 'B' cleaning or replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P010B ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Clean the sensor first; compare against the 'A' sensor.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →