Diagnose soonDrive gently and diagnose soon - a module stuck at max boost can overboost the engine.
The electronic module that controls your turbo's boost isn't responding correctly - its internal feedback doesn't match what the computer commands. Expect boost problems or limp mode.
Model notes: Common on electronically actuated variable-geometry turbos where the actuator is a sealed module bolted to the turbo.
Key facts
P00AF means turbocharger boost control 'A' module performance. The electronic module that controls your turbo's boost isn't responding correctly - its internal feedback doesn't match what the computer commands. Expect boost problems or limp mode. WrenchFair's published fair-price range for this repair is $200–$2200 parts and $150–$800 labor at independent shops.
WrenchFair rates P00AF a 3-of-5 DIY difficulty (“The module is part of the turbo assembly on many designs; scan-tool actuator tests confirm the failure.”) with a “Diagnose soon” driveability rating: Drive gently and diagnose soon - a module stuck at max boost can overboost the engine. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2013–2024 Ram 2500 (6.7L Cummins Turbo Diesel) — VGT turbo actuator failure and replacement (P00AF / P003A):Owner-verified
The actuator is a bolt-on part on the side of the Holset VGT turbo - the replacement itself is driveway-level, but a stock-style actuator must be calibrated to the turbo with a scan tool afterward (or buy the no-calibration City Diesel unit). Diagnose before you buy: P00AF almost always means the actuator, but P226B/P226C means the turbo itself has failed and a new actuator will not help.
Do this test first: Run the ECM's actuator test and watch commanded vs actual position
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P00AF on the 2013–2024 Ram 2500 — but the community-sourced VGT turbo actuator failure and replacement (P00AF / P003A) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
VGT actuator mounting fasteners: verify — Confirm against factory service info when replacing the actuator.
Tips
The symptom set is distinctive: sudden loss of boost and power, the exhaust brake stops working, and the check-engine light throws P00AF (turbo boost control module) and/or P003A (boost control position exceeded learning limit). If your exhaust brake died at the same time the power did, suspect the actuator first - they share the same mechanism.
Buy the right part: P00AF is almost always a bad actuator - but if you also have P226B or P226C, that signals a failed turbocharger, and a new actuator will not fix it. Do not spend $500+ on the wrong component.
With the actuator removed, work the sector gear on the turbo by hand: if it moves freely with light finger pressure, the turbo is fine and the actuator alone is the fix. Stiff or gritty vanes mean soot-stuck vanes and the turbo has to come out - no actuator will save it.
The calibration gotcha: a standard replacement actuator (Holset 5579127H, roughly $400-800) must be calibrated to the turbo with a scan tool after install - budget about $200 at a shop if you do not have the tool. The City Diesel billet actuator replaces the electronics and gear housing as a unit and needs NO calibration, which is why it is the owner-favorite DIY path; the 2013-2023 kit also fits 2007.5-2012 trucks.
2019+ trucks: a PCM software update (TSB 18-066-23) addresses false P0299 codes, and there is a separate service procedure for P0299 sensitivity - have the dealer check for the flash before buying parts. And always work the cheap end first: correct OEM air filter for your generation, intact charge-air-cooler hoses, and a clean MAP sensor (soot from the EGR clogs it and fakes boost readings).
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
overboost or underboost
reduced power / limp mode
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failing electronic boost control module (most common)
Sticking wastegate or vane mechanism overloading the module
Internal position sensor degradation
Wiring or connector fault to the module
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Run the ECM's actuator test and watch commanded vs actual position Tests: Internal position sensor degradation
Inspect the module's wiring and connector Tests: Wiring or connector fault to the module
Check that the wastegate/vane mechanism moves freely by hand (engine cool) Tests: Sticking wastegate or vane mechanism overloading the module
If the mechanism is free but the module can't track commands, replace the module Tests: Sticking wastegate or vane mechanism overloading the module
On many turbos the module only comes with the turbocharger assembly
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2024 Ram 2500: VGT turbo actuator failure and replacement (P00AF / P003A) — test first, then buy for this job.
The price range below is a national planning range for P00AF on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$200 – $2200
Labor$150 – $800
Turbo boost control module replacement (or turbocharger assembly if integrated). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P00AF ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The module is part of the turbo assembly on many designs; scan-tool actuator tests confirm the failure.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →