Diagnose soonA stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on.
Your engine's computer sees the exhaust camshaft and crankshaft out of sync on the bank-2 side. Check the sensors first (cheap), but a stretched timing chain is the classic mechanical cause.
Model notes: Bank 2 is the side opposite cylinder 1; 'B' is typically the exhaust camshaft.
Key facts
P0019 means crankshaft-camshaft correlation fault, bank 2 sensor B. Your engine's computer sees the exhaust camshaft and crankshaft out of sync on the bank-2 side. Check the sensors first (cheap), but a stretched timing chain is the classic mechanical cause. WrenchFair's published fair-price range for this repair is $40–$700 parts and $100–$2200 labor at independent shops.
WrenchFair rates P0019 a 3-of-5 DIY difficulty (“Sensor and wiring checks are easy DIY; confirming a stretched chain means opening up the timing cover.”) with a “Diagnose soon” driveability rating: A stretched chain behind this code can jump teeth and bend valves - diagnose it rather than driving on. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2009–2012 Chevrolet Traverse (3.6L V6 (LLT)) — Timing chain stretch (P0008/P0009 cam-crank correlation):Owner-verified
Front timing-cover teardown on the transverse 3.6L LLT — three chains (one primary, two secondary), tensioners, and guides. Owners report shops pulling the engine or dropping the cradle for access, so this is an advanced-DIY or shop job with a firm quote up front.
Do this test first: Inspect the bank 2 exhaust cam sensor and crank sensor wiring for damage or oil contamination
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0019 on the 2009–2012 Chevrolet Traverse — but the community-sourced Timing chain stretch (P0008/P0009 cam-crank correlation) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Timing components: verify — Chain/tensioner/guide bolt torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
The signature is P0008 and/or P0009 (camshaft-crankshaft correlation), often with P0016-P0019 companions. Nine times out of ten on these engines the cause is a stretched chain, per a veteran tech Q&A answer.
Before condemning the chains, verify oil level and condition — the tensioners are oil-fed, and low or degraded oil can set the same correlation codes.
GM's own diagnostic logic says a single failed cam actuator or solenoid will not set P0008; the code means chain alignment between crank and both cams on one bank.
GM issued special coverage 11340C for timing-chain wear on early 3.6L engines — check with a GM dealer by VIN before paying, since partial goodwill coverage has been reported by owners.
Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time). The 2013+ LFX engines got improved chains and a revised oil-life monitor — repeat failures concentrate on 2009-2012.
Do not keep driving on P0008/P0009 hoping it stays a code: a chain that jumps further can leave you with a dead engine on the road.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time).” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
reduced engine performance
hard starting or no start
rattling noise near the front of the engine
rough running
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Stretched timing chain or a belt that skipped a tooth (most common mechanical cause) 4 owner notes link this repair to P0019
Failed timing chain/belt tensioner 4 owner notes link this repair to P0019
Crankshaft or camshaft tone ring slipped or damaged 4 owner notes link this repair to P0019
Bad crankshaft or camshaft position sensor 4 owner notes link this repair to P0019
Damaged wiring to the cam or crank sensor 4 owner notes link this repair to P0019
VVT actuator stuck off its zero-degree position
Owner notes linked to P0019: 4 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Inspect the bank 2 exhaust cam sensor and crank sensor wiring for damage or oil contamination Tests: Damaged wiring to the cam or crank sensor
Check for companion correlation codes that point at the timing chain Tests: Stretched timing chain or a belt that skipped a tooth (most common mechanical cause)
Look up service bulletins for your engine
Compare cam and crank waveforms with a scope if available
Inspect timing chain/belt alignment, tensioner condition, and tone-ring security
Verify the bank 2 exhaust VVT actuator parks at zero degrees
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2009–2012 Chevrolet Traverse: Timing chain stretch (P0008/P0009 cam-crank correlation) — test first, then buy for this job.
The price range below is a national planning range for P0019 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $700
Labor$100 – $2200
Camshaft or crankshaft position sensor replacement if the sensor is at fault; timing chain, tensioner, and guide replacement if the chain stretched. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0019 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Sensor and wiring checks are easy DIY; confirming a stretched chain means opening up the timing cover.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →