Community-sourced DIY repair guides for the 2009–2012 Chevrolet Traverse, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Owner-verified repair guides
Throttle body / reduced engine power (special coverage) Owner-verified(3.6L LY7/LLT V6)
Dealer repair under the special coverage — no DIY needed if the car qualifies. The throttle body sits on the intake; the coverage pays for the part and labor.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “After replacement, disconnect the battery for about 30 minutes to clear the codes, and note that rough-running complaints on these cars should also get the oil level checked — low oil causes its own separate set of…” — as written in the note. First-timers often take twice this.
Torque specs
Throttle body fasteners: verify — Torque not confirmed from a forum source — confirm against factory service info; the intake-side fasteners thread into aluminum.
Tips
Know the pattern: rough running, the malfunction-indicator lamp, and a 'reduced engine power' message (sometimes paired with Service Stabilitrak warnings) trace to the throttle-position sensor in the electronic throttle body.
GM issued a special coverage for exactly this on 2009-2012 Traverse: 10 years or 120,000 miles from the original in-service date, regardless of ownership. Dealers replace the throttle body assembly and gasket on Bosch-equipped cars, or install a throttle-position-sensor kit on Hitachi-equipped cars — free.
Check VIN eligibility with a dealer before paying for a throttle body out of pocket; this coverage is why many owners got the repair at no charge.
Before replacing anything, inspect the throttle-body electrical connector and wiring for corrosion or damage — throttle-circuit wiring faults mimic a failed sensor and have fooled owners into repeat replacements.
After replacement, disconnect the battery for about 30 minutes to clear the codes, and note that rough-running complaints on these cars should also get the oil level checked — low oil causes its own separate set of problems on the 3.6L.
Front timing-cover teardown on the transverse 3.6L LLT — three chains (one primary, two secondary), tensioners, and guides. Owners report shops pulling the engine or dropping the cradle for access, so this is an advanced-DIY or shop job with a firm quote up front.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time).” — as written in the note. First-timers often take twice this.
Torque specs
Timing components: verify — Chain/tensioner/guide bolt torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
The signature is P0008 and/or P0009 (camshaft-crankshaft correlation), often with P0016-P0019 companions. Nine times out of ten on these engines the cause is a stretched chain, per a veteran tech Q&A answer.
Before condemning the chains, verify oil level and condition — the tensioners are oil-fed, and low or degraded oil can set the same correlation codes.
GM's own diagnostic logic says a single failed cam actuator or solenoid will not set P0008; the code means chain alignment between crank and both cams on one bank.
GM issued special coverage 11340C for timing-chain wear on early 3.6L engines — check with a GM dealer by VIN before paying, since partial goodwill coverage has been reported by owners.
Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time). The 2013+ LFX engines got improved chains and a revised oil-life monitor — repeat failures concentrate on 2009-2012.
Do not keep driving on P0008/P0009 hoping it stays a code: a chain that jumps further can leave you with a dead engine on the road.
Power steering pump whine / fluid and bleed procedure Owner-verified(3.6L V6)
Pump replacement and flush/bleed are driveway-friendly; the reservoir, high-pressure hose, and pump sit at the front of the engine bay. Bleeding air thoroughly is the fiddly part.
Typical difficulty: Moderate — based on 60 code guides for the steering repair area (an area-level estimate, not this exact job).
Torque specs
Pump/hose fittings: verify — Torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
Use DEXRON VI (GM bulletin 13-02-32-001B supersedes to DEXRON HP for listed cold-climate models) in the power steering — not generic power steering fluid. Owners running generic fluid report worse whine.
The classic DIY cure sequence: siphon or evacuate the reservoir, refill with fresh DEXRON VI, and bleed — front wheels off the ground, engine on, slow lock-to-lock turns, cap off, repeating until no bubbles.
Foam or bubbles in the reservoir while idling point to air entering the suction side (hose, adapter, or O-ring on top of the pump) — a leak on the low-pressure side causes whine under load even with a good pump.
Persistent loss of assist after a pump replacement is usually incomplete bleeding, not a second bad pump — several owners needed a day or two of driving before the noise fully settled.
Whine plus a visible drip at the rack: early Traverses also had steering-gear replacements, so check whether you're feeding a pump problem or a rack leak.
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 354 complaints for the 2009–2012 Chevrolet Traverse. 2012 was the worst year (354 complaints). Most-reported areas: engine, electronic stability control (esc), steering.
15V415000 (30/06/2015) — STRUCTURE:BODY:HATCHBACK/LIFTGATE General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to March 9, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15…
14V266000 (20/05/2014) — SEAT BELTS General Motors is recalling certain model year 2009-2014 Buick Enclave vehicles manufactured April 14, 2008, through May 14, 2014, Chevrolet Traverse vehicles manufactured June 6, 2008, through May 14, 2014, and GMC Acadia vehicles manufactured April 9, 2008, through May…
14V118000 (17/03/2014) — AIR BAGS:SIDE/WINDOW General Motors LLC (GM) is recalling certain model year 2008-2013 Buick Enclave and GMC Acadia and 2009-2013 Chevrolet Traverse and 2008-2010 Saturn Outlook vehicles. In the affected vehicles, increased resistance in the driver and passenger seat mounted side impact air…
12V151000 (09/04/2012) — VISIBILITY:WINDSHIELD WIPER/WASHER:LINKAGES GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2011-2012 CHEVROLET TRAVERSE, BUICK ENCLAVE, AND GMC ACADIA VEHICLES CURRENTLY REGISTERED IN ALASKA, COLORADO, CONNECTICUT, DELAWARE, IDAHO, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEW HAMPSHIRE, NEW JERSEY, NEW…
21V246000 (08/04/2021) — AIR BAGS:CRITICAL FASTENERS General Motors, LLC (GM) is recalling certain 2010-2015, 2017 Buick Enclave, 2010-2019 Chevrolet Traverse, and 2011-2016 GMC Acadia vehicles. The side curtain air bags may not be properly attached.
5 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
Factory service bulletins
We don't have factory bulletin data for the 2009–2012 Chevrolet Traverse yet.
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.
Torque specs marked “verify” were not published with a citable factory source — confirm them against the factory service manual for your exact engine before tightening. A trouble code does not prove a part needs replacement.