Diagnose soonA stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it.
Can I drive with P0009?
Can I drive with a P0009 code?
Short trips and gentle driving only, until you know the cause. A stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0009?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. A stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it.
Will P0009 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your engine's timing chain has stretched (or a tensioner is failing) on the bank-2 side, putting the camshafts out of sync with the crankshaft. Expect less power, worse mileage, and possible chain noise.
Model notes: Common on GM 3.6L LY7/LLT and 2.8L LP1 engines (Cadillac, Chevy Traverse, GMC Acadia, Buick Enclave, Suzuki XL7). Often appears alongside P0008 or cam/crank correlation codes.
Key facts
P0009 means engine position system performance bank 2. Your engine's timing chain has stretched (or a tensioner is failing) on the bank-2 side, putting the camshafts out of sync with the crankshaft. Expect less power, worse mileage, and possible chain noise. WrenchFair's published fair-price range for this repair is $250–$700 parts and $800–$2200 labor at independent shops.
WrenchFair rates P0009 a 4-of-5 DIY difficulty (“Diagnosing is easy; fixing means a timing chain job, which is a major teardown on most engines.”) with a “Diagnose soon” driveability rating: A stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2009–2012 Chevrolet Traverse (3.6L V6 (LLT)) — Timing chain stretch (P0008/P0009 cam-crank correlation):Owner-verified
Front timing-cover teardown on the transverse 3.6L LLT — three chains (one primary, two secondary), tensioners, and guides. Owners report shops pulling the engine or dropping the cradle for access, so this is an advanced-DIY or shop job with a firm quote up front.
Do this test first: Check oil level and condition - low oil accelerates chain wear
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0009 on the 2009–2012 Chevrolet Traverse — but the community-sourced Timing chain stretch (P0008/P0009 cam-crank correlation) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Timing components: verify — Chain/tensioner/guide bolt torque not confirmed from an owner source — confirm against factory service info before torquing.
Tips
The signature is P0008 and/or P0009 (camshaft-crankshaft correlation), often with P0016-P0019 companions. Nine times out of ten on these engines the cause is a stretched chain, per a veteran tech Q&A answer.
Before condemning the chains, verify oil level and condition — the tensioners are oil-fed, and low or degraded oil can set the same correlation codes.
GM's own diagnostic logic says a single failed cam actuator or solenoid will not set P0008; the code means chain alignment between crank and both cams on one bank.
GM issued special coverage 11340C for timing-chain wear on early 3.6L engines — check with a GM dealer by VIN before paying, since partial goodwill coverage has been reported by owners.
Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time). The 2013+ LFX engines got improved chains and a revised oil-life monitor — repeat failures concentrate on 2009-2012.
Do not keep driving on P0008/P0009 hoping it stays a code: a chain that jumps further can leave you with a dead engine on the road.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
Typical time: “Owner-reported bills: roughly $1,900-$3,000 for the full chain kit with labor (14.5-16 hours book time).” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
roughness under acceleration
decreased power
poor fuel economy
timing chain rattle or noise on startup
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Stretched timing chain on bank 2 (most common - known issue on GM 3.6L engines) 3 owner notes link this repair to P0009
Worn or failed timing chain tensioner or guides 3 owner notes link this repair to P0009
Crankshaft reluctor wheel slipped out of its indexed position 3 owner notes link this repair to P0009
Low oil level or pressure accelerating chain wear 3 owner notes link this repair to P0009
Worn camshaft phasers (less common)
Owner notes linked to P0009: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition - low oil accelerates chain wear Tests: Low oil level or pressure accelerating chain wear
Check technical service bulletins for your engine; revised chain kits exist for affected GM engines Tests: Stretched timing chain on bank 2 (most common - known issue on GM 3.6L engines)
Watch camshaft-vs-crankshaft correlation for bank 2 in live data Tests: Crankshaft reluctor wheel slipped out of its indexed position
Listen for chain rattle on cold startup
Plan a timing chain, tensioner, and guide replacement if correlation is off
Verify crankshaft reluctor wheel indexing during reassembly
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2009–2012 Chevrolet Traverse: Timing chain stretch (P0008/P0009 cam-crank correlation) — test first, then buy for this job.
The price range below is a national planning range for P0009 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$250 – $700
Labor$800 – $2200
Timing chain, tensioner, and guide replacement (the known fix on affected GM 3.6L engines). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0009 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Diagnosing is easy; fixing means a timing chain job, which is a major teardown on most engines.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →