Diagnose soonDrivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it.
Can I drive with P0011?
Can I drive with a P0011 code?
Short trips and gentle driving only, until you know the cause. Drivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0011?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Drivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it.
Will P0011 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your intake camshaft timing is stuck too far advanced on the cylinder-1 side - usually a stuck valve in the variable valve timing system. Expect hard starting, rough idle, and stalling.
Model notes: Common on Nissan (calls it 'camshaft variable timing control - bank 1 - performance'), Toyota, GM, Hyundai. An oil change alone resolves many cases.
Key facts
P0011 means intake camshaft timing over-advanced, bank 1. Your intake camshaft timing is stuck too far advanced on the cylinder-1 side - usually a stuck valve in the variable valve timing system. Expect hard starting, rough idle, and stalling. WrenchFair's published fair-price range for this repair is $40–$200 parts and $80–$300 labor at independent shops.
WrenchFair rates P0011 a 2-of-5 DIY difficulty (“Often fixed with a solenoid replacement and fresh oil; verifying cam timing needs a scan tool with live data.”) with a “Diagnose soon” driveability rating: Drivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2008 Nissan 350Z (3.5L VQ35HR V6) — VQ35HR oil gallery gaskets: low oil pressure with no leak (P0011/P0021):Owner-verified
This is a timing-cover-off job: front of the engine opened, both oil gallery cover plates removed. Given the labor, replace BOTH gallery gaskets, the cover o-rings, and the fasteners together - never reopen this job for one gasket.
Do this test first: Check oil level, condition, and viscosity - change it if dirty or wrong, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0011 on the 2007–2008 Nissan 350Z — but the community-sourced VQ35HR oil gallery gaskets: low oil pressure with no leak (P0011/P0021) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Gallery cover plate fasteners: verify — Even, uniform torque across the gallery plates is the critical detail; exact spec not confirmed from a forum source - confirm against factory service info before torquing.
Tips
2007-2008 VQ35HR cars losing oil pressure at idle with no visible leak and no oil consumption are likely seeping through the rear timing-cover oil gallery gaskets - the factory paper gaskets separate over time.
Symptoms: low gauge readings at idle/low rpm, excessive VCT rattle, P0011 or P0021 codes.
Replace BOTH gallery gaskets (small/lower and large/upper) with the updated metal-reinforced composite gaskets plus new cover o-rings and hardware that torques evenly.
Do not keep driving on low oil pressure to 'see if it gets worse' - oil starvation kills the engine long before the gaskets finish failing.
While the timing cover is off, inspect the timing components and consider the water pump - the labor overlap is total.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
hard starting
poor or rough idle
stalling
hesitation on acceleration
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
VVT oil control solenoid stuck open, feeding continuous oil flow to the phaser (most common) 2 owner notes link this repair to P0011
Incorrect camshaft timing from prior timing-chain/belt work 9 owner notes link this repair to P0011
Dirty or wrong-viscosity oil affecting VVT operation
Worn camshaft phaser stuck in the advanced position 9 owner notes link this repair to P0011
Wiring fault holding the solenoid energized 2 owner notes link this repair to P0011
Owner notes linked to P0011: 11 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level, condition, and viscosity - change it if dirty or wrong, then clear and retest Tests: Dirty or wrong-viscosity oil affecting VVT operation
Watch commanded vs. actual intake camshaft angle on bank 1: if actual stays advanced with no command, the solenoid or phaser is stuck Tests: Worn camshaft phaser stuck in the advanced position
Remove and inspect the bank 1 intake VVT solenoid for sludge, debris, or a stuck pintle; test or replace it Tests: VVT oil control solenoid stuck open, feeding continuous oil flow to the phaser (most…
Check the solenoid control wiring for a short holding it energized Tests: Wiring fault holding the solenoid energized
If the solenoid is good, verify base camshaft timing marks - a mistimed chain/belt from prior work causes this too
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2008 Nissan 350Z: VQ35HR oil gallery gaskets: low oil pressure with no leak (P0011/P0021) — test first, then buy for this job.
The price range below is a national planning range for P0011 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $200
Labor$80 – $300
VVT oil control valve (solenoid) replacement, often with an oil change. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0011 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Often fixed with a solenoid replacement and fresh oil; verifying cam timing needs a scan tool with live data.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →