P0011

P0011 on a 2008–2013 Infiniti G37: Intake camshaft timing over-advanced, bank 1

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0011 on a 2010–2017 Chevrolet Equinox · 2015–2016 Honda Fit · 2008–2012 Infiniti G37 · 2008–2013 Infiniti G37 · 2016–2019 Mercedes-Benz GLC · 2012–2018 Mercedes-Benz GLE
Show all 10 vehicles with this code

2007–2008 Nissan 350Z · 2009–2020 Nissan 370Z · 2005–2010 Nissan Frontier · 2010–2014 Volkswagen Golf/GTI

DIY difficulty 2/5

Can I drive with P0011?

Can I drive with a P0011 code?

Short trips and gentle driving only, until you know the cause. Drivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0011?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Drivability is poor and stalling in traffic is a real risk - diagnose soon rather than living with it.

Will P0011 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

Your intake camshaft timing is stuck too far advanced on the cylinder-1 side - usually a stuck valve in the variable valve timing system. Expect hard starting, rough idle, and stalling.

Model notes: Common on Nissan (calls it 'camshaft variable timing control - bank 1 - performance'), Toyota, GM, Hyundai. An oil change alone resolves many cases.

Key facts

☑ Before you buy parts — check these first:
On your 2008–2013 Infiniti G37 (3.7L VQ37VHR V6) — Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair: Owner-verified
Front of the engine - solenoids are externally accessible, so this is a diagnose-and-swap job, not a timing-cover job.
Do this test first: Check oil level, condition, and viscosity - change it if dirty or wrong, then clear and retest
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0011 on the 2008–2013 Infiniti G37 — but the community-sourced Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: myg37.com 'P0021 P0011 VVT Solenoid' - G37 owner: after fixing the rear timing cover (gallery) gasket with oil pressure confirmed good, P0524 and P0021 persisted until the faulty bank 2 intake timing solenoid was replaced - both codes then cleared · myg37.com 'P0011, P0021, P0524, p0075, p0081, p0340, p0345 check before replacing gasket' - warns against jumping straight to the gallery gasket: the VTC phaser position ring can slip and IVT solenoids can fail with the same codes; FSM lists intake valve control solenoid valve among the possible causes of P0011/P0021

Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0011: 11 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check oil level, condition, and viscosity - change it if dirty or wrong, then clear and retest Tests: Dirty or wrong-viscosity oil affecting VVT operation
  2. Watch commanded vs. actual intake camshaft angle on bank 1: if actual stays advanced with no command, the solenoid or phaser is stuck Tests: Worn camshaft phaser stuck in the advanced position
  3. Remove and inspect the bank 1 intake VVT solenoid for sludge, debris, or a stuck pintle; test or replace it Tests: VVT oil control solenoid stuck open, feeding continuous oil flow to the phaser (most…
  4. Check the solenoid control wiring for a short holding it energized Tests: Wiring fault holding the solenoid energized
  5. If the solenoid is good, verify base camshaft timing marks - a mistimed chain/belt from prior work causes this too

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2008–2013 Infiniti G37: Intake valve timing (IVT) solenoids: P0075/P0081 and P0011/P0021 that survive a gasket repair — test first, then buy for this job.
The price range below is a national planning range for P0011 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $200
Labor$80 – $300

VVT oil control valve (solenoid) replacement, often with an oil change. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0011 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Often fixed with a solenoid replacement and fresh oil; verifying cam timing needs a scan tool with live data.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

🔍 Seeing multiple codes? Combinations mean something different than codes alone. How to read code combinations →
Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →