Diagnose soonThe engine runs on fixed cam timing, so performance and economy suffer - fix it, but it's not a stop-driving emergency.
The electric valve that adjusts your intake camshaft timing on the cylinder-1 side has an electrical fault - usually a bad solenoid or damaged wiring. The engine runs, but with the cam timing stuck in one position.
Model notes: Very common code across Toyota, GM, Ford, Honda, VW/Audi, Hyundai. On some engines the solenoid screens clog with sludge - cleaning can work, but replacement is more reliable.
Key facts
P0010 means intake camshaft actuator circuit fault, bank 1. The electric valve that adjusts your intake camshaft timing on the cylinder-1 side has an electrical fault - usually a bad solenoid or damaged wiring. The engine runs, but with the cam timing stuck in one position. WrenchFair's published fair-price range for this repair is $40–$150 parts and $80–$250 labor at independent shops.
WrenchFair rates P0010 a 2-of-5 DIY difficulty (“The VVT solenoid is usually an accessible bolt-on part; the main work is confirming it's the solenoid and not the wiring.”) with a “Diagnose soon” driveability rating: The engine runs on fixed cam timing, so performance and economy suffer - fix it, but it's not a stop-driving emergency. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 2,692 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Engine And Engine Cooling) — see the latest ones
On your 2010–2017 Chevrolet Equinox (2.4L Ecotec I4) — VVT camshaft actuator solenoids (P0010/P0013):Owner-verified
Both solenoids sit on top of the engine under the plastic engine cover — no intake manifold removal needed. One 10mm bolt holds each unit.
Do this test first: With the engine warm, inspect the bank 1 intake VVT solenoid wiring and connector for damage, corrosion, or loose pins, and repair as needed
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0010 on the 2010–2017 Chevrolet Equinox — but the community-sourced VVT camshaft actuator solenoids (P0010/P0013) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
VVT solenoid bolt (10mm): verify — Bolt torque not confirmed from a forum source — snug by hand; confirm against factory service info before torquing.
Tips
The pattern: check-engine light with P0010/P0011 (intake) or P0013/P0014 (exhaust), sometimes with stalling or cutting out at low speeds and stoplights. Owners in the repair logs report replacing these solenoids multiple times — roughly yearly on high oil-consumption engines.
The easy electrical test before buying parts: unplug each solenoid and check resistance across the terminals — spec is 8-13 ohms. Also check for a short to ground from each terminal. Any solenoid out of spec gets replaced; a technician notes it is common for both to fail, so if one is dead, test the other.
Identification: gray connector = intake solenoid (GM 12655420), black connector = exhaust solenoid (GM 12655421). They come as a matched pair from most parts sellers and are inexpensive.
The swap: pop the engine cover, disconnect the electrical tab, remove the single 10mm bolt, and pull the solenoid straight out. Lubricate the new O-rings with fresh oil before installing so they seat without tearing.
Before condemning the solenoid on a P0011/P0014 over-advance code, check the fine filter screens on the actuator valves — clogged screens from dirty oil cause the same codes. Cleaning the screens has fixed it for some owners without new parts.
Root-cause note: these solenoids fail early on engines that burn oil or run long oil-change intervals — the same neglected-oil problem behind the timing chain and PCV issues on this engine. Fix the oil discipline or the new solenoids will follow the old ones.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
rough running or rough idle
poor acceleration
decreased fuel economy
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed VVT oil control valve (solenoid) for the bank 1 intake camshaft (most common)
Open or shorted wiring in the VVT actuator circuit, including rodent damage
Corroded or loose connector at the solenoid
Blown fuse feeding the solenoid circuit
PCM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
With the engine warm, inspect the bank 1 intake VVT solenoid wiring and connector for damage, corrosion, or loose pins, and repair as needed Tests: Failed VVT oil control valve (solenoid) for the bank 1 intake camshaft (most common)
Check the fuse feeding the VVT solenoid circuit Tests: Blown fuse feeding the solenoid circuit
Unplug the solenoid and measure its internal resistance against the factory specification - an open or shorted winding means replacement Tests: Open or shorted wiring in the VVT actuator circuit, including rodent damage
Check the harness for continuity back to the PCM and for shorts to ground or power
Command the solenoid on and off with a bi-directional scan tool if available and listen/feel for the click
Clear the code and retest; if the circuit is good and the code returns, suspect the PCM driver
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2010–2017 Chevrolet Equinox: VVT camshaft actuator solenoids (P0010/P0013) — test first, then buy for this job.
The price range below is a national planning range for P0010 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $150
Labor$80 – $250
VVT oil control valve (solenoid) replacement for the bank 1 intake camshaft. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0010 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — The VVT solenoid is usually an accessible bolt-on part; the main work is confirming it's the solenoid and not the wiring.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →