Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it.
Your engine's timing chain has stretched (or a tensioner is failing), so the camshafts on one side of the engine are out of sync with the crankshaft. You'll feel less power and worse mileage, and it only gets worse.
Model notes: Extremely common on GM 3.6L LY7/LLT (Cadillac CTS/SRX, Chevy Traverse, GMC Acadia, Buick Enclave, Saturn Outlook, Suzuki XL7) and 2.8L LP1. Revised parts exist - don't reinstall the old-design chain.
Key facts
P0008 means engine position system performance bank 1. Your engine's timing chain has stretched (or a tensioner is failing), so the camshafts on one side of the engine are out of sync with the crankshaft. You'll feel less power and worse mileage, and it only gets worse. WrenchFair's published fair-price range for this repair is $250–$700 parts and $800–$2200 labor at independent shops.
WrenchFair rates P0008 a 4-of-5 DIY difficulty (“Diagnosing is easy; fixing means a timing chain job, which is a major teardown on most engines.”) with a “Diagnose soon” driveability rating: A stretched chain only gets looser - if it jumps teeth, valves meet pistons. Schedule the repair; don't road-trip on it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
roughness under acceleration
decreased power
poor fuel economy
timing chain rattle or noise on startup
Likely causes
Stretched timing chain on bank 1 (most common - a known issue on GM 3.6L engines) 3 owner notes link this repair to P0008
Worn or failed timing chain tensioner or guides 3 owner notes link this repair to P0008
Crankshaft reluctor wheel slipped out of its indexed position 3 owner notes link this repair to P0008
Low oil level or pressure accelerating chain wear 3 owner notes link this repair to P0008
Worn camshaft phasers (less common)
Owner notes linked to P0008: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition first - low oil accelerates chain stretch and can mimic timing faults Tests: Stretched timing chain on bank 1 (most common - a known issue on GM 3.6L engines)
Look up technical service bulletins for your engine; some GM 3.6L engines have revised chain kits Tests: Stretched timing chain on bank 1 (most common - a known issue on GM 3.6L engines)
Use live data to watch camshaft-vs-crankshaft correlation on bank 1 at idle and under load Tests: Crankshaft reluctor wheel slipped out of its indexed position
Listen for chain rattle on cold startup, a classic stretched-chain tell Tests: Stretched timing chain on bank 1 (most common - a known issue on GM 3.6L engines)
If correlation is off and the chain is noisy or high-mileage, plan a timing chain, tensioner, and guide replacement
After replacement, verify the crankshaft reluctor wheel is correctly indexed before reassembly
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$250 – $700
Labor$800 – $2200
Timing chain, tensioner, and guide replacement (the known fix on affected GM 3.6L engines). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0008 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Diagnosing is easy; fixing means a timing chain job, which is a major teardown on most engines.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →