Diagnose soonBraking takes much more effort without boost — drive carefully and get it fixed promptly.
A brake warning comes on and the pedal gets much harder — the booster's power electronics have failed internally.
Key facts
C0595 means brake Booster Internal Power Driver Range/Performance. A brake warning comes on and the pedal gets much harder — the booster's power electronics have failed internally. WrenchFair's published fair-price range for this repair is $400–$1200 parts and $250–$550 labor at independent shops.
WrenchFair rates C0595 a 4-of-5 DIY difficulty (“Internal electronics — there's no component-level fix; the booster assembly gets replaced.”) with a “Diagnose soon” driveability rating: Braking takes much more effort without boost — drive carefully and get it fixed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 2,203 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Engine And Engine Cooling) — see the latest ones
On your 2016–2019 Chevrolet Malibu (1.5L Turbo, 2.0L Turbo) — Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202):Owner-verified
Dealer scan tool and programming — no DIY disassembly. The value for owners is knowing the documented fix before a shop sells parts.
Do this test first: 1. Verify the booster's power and ground are clean — rule out the feed first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0595 on the 2016–2019 Chevrolet Malibu — but the community-sourced Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
EBCM programming: verify — No mechanical fasteners — dealer programming procedure. The TSB stresses stable battery voltage during programming.
Tips
Symptom cluster: "Service Stabilitrak" on the driver info center PLUS inoperative rear brake lights and the traction-control light — with DTCs C0595, C0277 (brake pedal position sensor circuit codes), and U0422.
Per GM TSB 19-NA-202 (September 2019, Malibu 2016–2019), the cause is a software anomaly in the electronic brake control module — and the bulletin explicitly says DO NOT replace the brake pedal position sensor. The correction is reprogramming the EBCM with the latest software.
Owner value: if a shop quotes a brake pedal position sensor (or a brake booster control module) for this exact symptom cluster, point them at TSB 19-NA-202 first — the software update is the documented fix and may be covered.
Safety note: with the stop lamps inoperative the car is not road-legal at night. Check whether your brake lights work before driving, and treat this as fix-soon.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
brake system warning light on
brake pedal much harder than normal
brake assist unavailable message
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
power driver overheated and failed
voltage spike damaged the driver
booster control module internal fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Verify the booster's power and ground are clean — rule out the feed first.
2. Check for related overvoltage or overheating codes.
3. If the feed is good, the internal driver has failed — replace the booster assembly. Tests: booster control module internal fault
4. Calibrate the new booster per the service procedure. Tests: booster control module internal fault
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2016–2019 Chevrolet Malibu: Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202) — test first, then buy for this job.
The price range below is a national planning range for C0595 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$400 – $1200
Labor$250 – $550
Electric brake booster replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0595 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Internal electronics — there's no component-level fix; the booster assembly gets replaced.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →