C0595

C0595 on a 2016–2019 Chevrolet Malibu: Brake Booster Internal Power Driver Range/Performance

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: C0595 on a 2016–2019 Chevrolet Malibu

DIY difficulty 4/5

A brake warning comes on and the pedal gets much harder — the booster's power electronics have failed internally.

Key facts

☑ Before you buy parts — check these first:
On your 2016–2019 Chevrolet Malibu (1.5L Turbo, 2.0L Turbo) — Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202): Owner-verified
Dealer scan tool and programming — no DIY disassembly. The value for owners is knowing the documented fix before a shop sells parts.
Do this test first: 1. Verify the booster's power and ground are clean — rule out the feed first.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0595 on the 2016–2019 Chevrolet Malibu — but the community-sourced Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202) note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: TSB summary · owner complaints

Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. 1. Verify the booster's power and ground are clean — rule out the feed first.
  2. 2. Check for related overvoltage or overheating codes.
  3. 3. If the feed is good, the internal driver has failed — replace the booster assembly. Tests: booster control module internal fault
  4. 4. Calibrate the new booster per the service procedure. Tests: booster control module internal fault

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2016–2019 Chevrolet Malibu: Service Stabilitrak + dead brake lights — EBCM software (TSB 19-NA-202) — test first, then buy for this job.
The price range below is a national planning range for C0595 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$400 – $1200
Labor$250 – $550

Electric brake booster replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0595 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Internal electronics — there's no component-level fix; the booster assembly gets replaced.

Watch this repair on YouTube

Parts & tools

ABS / wheel-speed toolkit — what the job actually takes

Torque specs: Wheel-speed sensor bolts: typically 8–12 Nm. (Caliper bracket bolts are far tighter — 90–140 Nm — don’t confuse them.)

Pro tip: Inspect the tone ring/reluctor for cracks and debris first — the sensor itself is often innocent.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →