Community-sourced DIY repair guides for the 2018–2024 Toyota Camry, plus NHTSA complaints and recalls sliced to these model years. Every guide below comes from real owner-community procedures with sources.
Foam engine cover pulls straight off (no bolts) to expose the 4 ignition coils on the valve cover. Coils are Denso 90919-A2009, each held by one small-head 8mm bolt (the factory manual flags these as small-head bolts). A 9/16" deep spark-plug socket reaches the plugs in the wells.
Typical difficulty: Easy — based on 64 code guides for the ignition repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide
P0300 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Bank 1 Sensor 1 (upstream) is a wideband air-fuel ratio sensor, not a conventional narrowband O2 — the downstream is the heated oxygen sensor (per the factory service manual's monitor description). TRQ's video walkthrough covers the upstream sensor replacement for the full 2018-2024 Camry range, demonstrated on a 2022 LE 2.5L AWD. Soak the sensor threads with rust penetrant well before the attempt — seized threads are the known pain point on these sensors.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide
P0131 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The thermostat is not a standalone mechanical unit — it's an electrically-controlled 'water inlet with thermostat sub-assembly' with an electrical connector and a heater circuit monitored by the ECM. The A25A-FKS also uses an electric water pump, not a belt-driven one.
Typical difficulty: Moderate — based on 294 code guides for the cooling repair area (an area-level estimate, not this exact job).
Sources: owner forum / guide · owner forum / guide · owner forum / guide
P0117 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Caliper slide bolts are 14 mm (hold the slider flats with a 17 mm wrench); caliper bracket bolts are 17 mm. Compress the piston by placing an old pad against it and squeezing it in with a C-clamp until fully seated. Rusted rotors are common — thread a lug nut on to temporarily hold the new rotor against the hub while you position the bracket. New pads swap into the existing bracket hardware; apply brake grease to the pad contact points.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
Sources: iFixit — Front brake pads & rotors, 2018-2024 Toyota Camry (caliper pins 25 ft-lb, reservoir/pedal-pump steps) · iFixit — Bracket install step (17 mm bolts to 79 ft-lb; lug nut to hold rotor) · 1A Auto — Camry brake kit install transcript (25 ft-lb caliper bolts, lug nuts, star pattern) · YouTube — How to change 2018 Camry front brake pads (14 mm/17 mm bolts, grease contact points, wear indicators) · tireswheels.org — 2018 Toyota Camry lug nut torque specs (76-83 ft-lb, star pattern, 50-100 mile re-torque)
C0035 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
12V battery is in the engine bay on the right (passenger) side of the vehicle. Correct group size is H5 (BCI Group 47); confirm terminal layout before buying. Terminal clamp bolts are 10 mm; the hold-down bracket bolt is 12 mm (use an extension). Disconnect negative terminal first, then positive; reverse on install (positive first, then negative).
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Typical time: “Rough/stalling idle after a disconnect is common on Toyotas: with the engine warm, hold it around 2000 RPM in drive for about 5 minutes so the ECU relearns fuel trims and idle (idle-reset walkthrough).” — as written in the note. First-timers often take twice this.
Sources: MobileBattery — 2018 Toyota Camry battery replacement (right-side location, Group H5, 10 mm terminals, 12 mm hold-down) · YouTube — reset idle after disconnecting battery terminal (Toyota Camry, ~2000 RPM for ~5 min fuel-trim relearn) · YouTube — Toyota/Lexus rough idle after battery change: idle reset relearn procedure (Camry) · YouTube — Toyota/Lexus window reset (hold 5 sec at bottom, 5 sec at top; happens after battery change) · YouTube — 2018-2023 Toyota Camry battery replacement (2.5L & 3.5L how-to) · Jerry Lambert Automotive — How to reset systems after battery replacement (memory saver, window recalibration)
P0560 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The 2.5L A25A-FKS alternator is removed from the TOP of the engine bay — no wheel-well or undertray access needed. Disconnect the negative battery cable first (10 mm clamp bolt) to prevent shorts on the charging circuit. Remove the plastic cover over the alternator positive stud, pull the 10 mm nut off the stud, and unplug the field connector (press the lock tab; grip only the plastic connector). Photograph the serpentine belt routing, then rotate the tensioner counter-clockwise with a 14 mm wrench and slip the belt off the alternator pulley. Remove the 10 mm bolt holding the engine wire-harness bracket, then the upper 12 mm mounting bolt and the two 12 mm lower mounting nuts; pull the alternator straight rearward off the studs and lift it upward out of the engine compartment. Caution: the charging-terminal stud passes through an insulating bushing — when reinstalling, tighten the 10 mm terminal nut only until snug.
Typical difficulty: Involved — based on 854 code guides for the battery repair area (an area-level estimate, not this exact job).
Sources: iFixit — How to replace the alternator in your 2018-2024 Toyota Camry (2.5L 4-cyl): battery disconnect, terminal, connector, belt/tensioner, harness bracket steps · iFixit — Alternator removal step (12 mm upper bolt, two 12 mm lower stud nuts; connector lock tab) · iFixit — Alternator lift-out step (pull rearward off studs, lift upward out of engine compartment) · Jalopnik — Replace an alternator (battery disconnect safety, tensioner release, belt deflection check)
P0620 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
No tank drop needed: the XV70 has a rear floor service hole cover under the rear seat cushion. Remove the rear seat cushion assembly, then peel off the rear floor service hole cover (it is sealed with butyl tape) to expose the fuel suction tube with pump and gauge assembly. Disconnect the fuel pump electrical connector, then the fuel return/main tube joints — release the tube joint clips, pull the joints off by hand, do not scratch the O-rings, and do not bend, twist, or kink the nylon tubes; cap disconnected joints with a plastic bag. Mark the assembly's paint alignment to the tank before removing the fuel pump gauge retainer, which can require up to 200 N·m (148 ft-lbf) to break loose (SST, a two-person job). Do not bend the fuel sender gauge arm when lifting the assembly out, and replace the fuel suction tube set gasket. Reassembly is done by aligning the copied start-of-threads and fully-tightened marks, not by a torque figure.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
Typical time: “The whole assembly (pump + integrated level sending unit) is typically replaced as a unit on this car; a pro-tech time of about 1 hour is common, with Denso as the OEM pump maker.” — as written in the note. First-timers often take twice this.
Sources: Toyota repair manual — fuel pump removal (RM3026E, XV70 Camry): rear floor service hole cover, tube joints, gauge retainer, SST, 200 N·m note, alignment marks · TRQ how-to video — fuel pump replacement on 2018–2024 Camry (done on a 2022 LE 2.5L), ~1h6m · Torque News — Toyota fuel pump recall coverage including 2018–2019 Camry
P0087 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
The A25A-FKS uses a drive-by-wire electronic throttle body mounted on the intake manifold. Remove the plastic engine cover, then loosen the clamp on the intake air hose at the air cleaner outlet and move the hose aside to expose the throttle body — no removal from the manifold is needed to clean it. Spray throttle body cleaner and wipe the bore and both sides of the plate with a soft cloth or brush; if you open the plate, move it VERY slowly — if you hear the internal motor, you are moving too fast. If you do remove the throttle body from the manifold, install a new gasket; reusing the old one risks vacuum leaks. Keep the removed unit upright and do not flood the motor/gear housing with solvent.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Sources: The Car Care Nut (Toyota master diagnostic technician) — how to clean a Toyota throttle body safely, gasket rule on removal · Toyota technician walkthrough — clean Toyota/Lexus throttle in place, move plate slowly, new gasket if removed · TacomaWorld forum thread — Camry throttle body cleaning: high idle after cleaning fixed by disconnecting the battery 10 minutes · TSB walkthrough video — T-SB-0005-24 cold-weather throttle actuator issue on 2020–2022 Camry A25A-FKS (ECM reflash + fuel pump replacement)
No owner reports yet — fixed this yourself? tell us how
The 8-speed UA80 has no dipstick — level is set with the overflow/standpipe method. Drain plug is a 10mm hex on the pan; the level-check overflow tube inside the drain is a 6mm hex; the fill plug is a 24mm bolt on the side of the case (remove the splash shield to reach it). Drain about 3 quarts with the straw removed, then refill by hand pump through the fill hole (there is no gravity-fill access) with slightly more Toyota Genuine ATF WS than you drained — WS fluid only. To set the level: with the overflow tube installed, warm the fluid to 95–113°F (35–45°C), engine running, shift slowly P to D and back to P (about 3 seconds in each range) to circulate, then pull the drain plug and let it drain until it drops from a stream to a trickle, and reinstall. The 6mm level-check plug is hand-tight only; replace the drain plug crush washer. Do not remove the overflow tube/standpipe for a level check — only remove it to drain.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
Sources: AllData/UA80E factory procedure mirrored on ClubLexus — 'Use Toyota Genuine ATF WS', refill plug steps, shift-circulation procedure · Camry-specific video — 2018–2022 Camry 2.5 UB80E ATF change: 24mm fill plug, 10mm hex drain (15 ft-lbs), 6mm check plug, 95–113°F target temp · BobIsTheOilGuy forum — UA80 drain and refill takes ~3 qt; pumping is the only refill option; level via temperature/straw procedure · IH8MUD forum — 8-speed level procedure: warm to ~115°F, pull overflow pipe, drain to trickle, finish before ~125°F; never remove the stand pipe just to check
P0700 on this Toyota Camry — full diagnosis guide →
No owner reports yet — fixed this yourself? tell us how
Difficulty lines above are area-level estimates from code guides for that repair area, not the exact job; times are quoted verbatim from the notes themselves — first-timers often take twice this.
How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
NHTSA recorded 324 complaints for the 2018–2024 Toyota Camry. 2020 was the worst year (274 complaints). Most-reported areas: electrical system, engine, air bags.
Counts are NHTSA complaints filed for these model years, via the NHTSA API. See data for all Camry years →
4 recall campaigns touch these years. Check your VIN at nhtsa.gov/recalls.
NHTSA has published 610 manufacturer communications (service bulletins, dealer notices) covering the 2018–2024 Toyota Camry.
Most cited systems: Equipment (266), Electrical System (174), Structure (57), Engine (53), Engine And Engine Cooling (38).
Latest bulletins:
Counts are deduplicated NHTSA manufacturer communications for these model years, via the NHTSA safety-issues API. Look up bulletins for your exact VIN at nhtsa.gov/recalls under Manufacturer Communications.