Diagnose soonYour regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads.
Your car's ABS computer found an electrical problem in the left front wheel speed sensor wiring. Your regular brakes work fine, but ABS and traction control may be disabled.
Key facts
C0035 means left Front Wheel Speed Sensor Circuit Malfunction. Your car's ABS computer found an electrical problem in the left front wheel speed sensor wiring. Your regular brakes work fine, but ABS and traction control may be disabled. WrenchFair's published fair-price range for this repair is $40–$180 parts and $90–$250 labor at independent shops.
WrenchFair rates C0035 a 3-of-5 DIY difficulty (“Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.”) with a “Diagnose soon” driveability rating: Your regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 610 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Structure) — see the latest ones
On your 2018–2024 Toyota Camry (2.5L 4-cyl (A25A-FKS)) — Front brake pads & rotors:Owner-verified
Caliper slide bolts are 14 mm (hold the slider flats with a 17 mm wrench); caliper bracket bolts are 17 mm. Compress the piston by placing an old pad against it and squeezing it in with a C-clamp until fully seated. Rusted rotors are common — thread a lug nut on to temporarily hold the new rotor against the hub while you position the bracket. New pads swap into the existing bracket hardware; apply brake grease to the pad contact points.
Do this test first: 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0035 on the 2018–2024 Toyota Camry — but the community-sourced Front brake pads & rotors note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Caliper bracket bolts: 79 ft-lb (107 N·m) — 17 mm bolts; torque per the 2018-2024 Camry iFixit brake guide.
Caliper slide bolts: 25 ft-lb (34 N·m) — 14 mm bolts; hold slider flats with 17 mm wrench while torquing, per the iFixit guide.
Lug nuts: 76-83 ft-lb (103-113 N·m) — 2018 Camry spec across 16-19 inch wheels; torque in star pattern.
Tips
Open/loosen the brake-fluid reservoir cap before compressing the pistons — fluid pushed back can overflow a full reservoir; verify the level sits between MIN and MAX after the job (iFixit guide).
Pump the brake pedal until it feels solid before driving, then test drive at low speed to confirm proper operation (iFixit guide).
Re-torque the lug nuts after driving 50-100 miles to account for settling.
Watch the wear-indicator tab position when removing the old pads so the new pads go in the same orientation (2018 Camry DIY video).
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
abs warning light on
traction control or stability control light on
cruise control stops working
speedometer may read wrong
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
failed wheel speed sensor (most common) 39 owner notes link this repair to C0035
wiring break or chafing at the wheel-arch flex point 39 owner notes link this repair to C0035
corroded or loose sensor connector
damaged tone ring
ABS module failure is possible but uncommon - rule out wiring and sensors first
Owner notes linked to C0035: 40 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
2. Watch the left front wheel speed in ABS live data at low speed. A dead, jumpy, or mismatched reading confirms the problem corner. Tests: failed wheel speed sensor (most common)
3. Unplug the left front sensor and inspect the connector for corrosion, moisture, or bent pins. Tests: corroded or loose sensor connector
4. Trace the sensor harness along the wheel-arch flex point and look for chafing, cracks, or breaks. Tests: wiring break or chafing at the wheel-arch flex point
5. Inspect the tone ring for cracked or missing teeth while the wheel is off.
6. If the wiring and tone ring check out, replace the left front wheel speed sensor — it is the most common fix.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2018–2024 Toyota Camry: Front brake pads & rotors — test first, then buy for this job.
Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors.
The price range below is a national planning range for C0035 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $180
Labor$90 – $250
A wheel speed sensor replacement, often $150-$350 installed at an independent shop. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0035 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →