U3018: Control Module Input Power Circuit A/B Correlation
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car may not start or may lose power unexpectedly - find the dead feed before it strands you.
Your car's computer compares two power signals that should agree, and they don't - like one wire saying the key is on while the other says it isn't. Usually a bad relay, fuse, or wire on one of the two circuits, not a dead computer.
Key facts
U3018 means control Module Input Power Circuit A/B Correlation. Your car's computer compares two power signals that should agree, and they don't - like one wire saying the key is on while the other says it isn't. Usually a bad relay, fuse, or wire on one of the two circuits, not a dead computer. WrenchFair's published fair-price range for this repair is $55–$580 parts and $75–$500 labor at independent shops.
WrenchFair rates U3018 a 3-of-5 DIY difficulty (“The trick is identifying which two feeds are being compared; after that it's standard fuse-and-relay testing on each side.”) with a “Diagnose soon” driveability rating: The car may not start or may lose power unexpectedly - find the dead feed before it strands you. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
no crank or no start
dash power inconsistent with key position
some systems powered while others are dead
code sets only in certain key positions
Likely causes
Failing relay on one of the two compared circuits (most common)
Blown fuse on one feed
Worn ignition switch contact feeding one side
Wiring fault, corroded connector, or high resistance on one side
Module internal comparison fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Identify the two feeds the module is comparing from the service information.
Check the fuse and relay on each feed - the fault is almost always on one side, not both. Tests: Blown fuse on one feed
With the key in the relevant position, compare actual voltage on both feeds at the module connector. Tests: Wiring fault, corroded connector, or high resistance on one side
Trace the dead or weak side back through its relay, fuse, and wiring until you find the break. Tests: Wiring fault, corroded connector, or high resistance on one side
Repair the faulty side, clear the code, and confirm both feeds agree in every key position.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$55 – $580
Labor$75 – $500
Relay or fuse replacement on the faulty feed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U3018 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The trick is identifying which two feeds are being compared; after that it's standard fuse-and-relay testing on each side.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →