Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonDepending on which module failed, anything from a dead accessory to a no-start is possible - find out which module before driving far.
One of your car's computer modules failed its own internal self-test. It may genuinely be bad, but weak power, a bad ground, or a corroded connector can make a healthy module look broken - so check power and wiring before buying a module.
Key facts
U3000 means control Module. One of your car's computer modules failed its own internal self-test. It may genuinely be bad, but weak power, a bad ground, or a corroded connector can make a healthy module look broken - so check power and wiring before buying a module. WrenchFair's published fair-price range for this repair is $345–$2880 parts and $150–$850 labor at independent shops.
WrenchFair rates U3000 a 5-of-5 DIY difficulty (“Proving a module is truly dead needs a factory-level scan tool and a wiring diagram; replacement modules almost always need dealer or locksmith programming.”) with a “Diagnose soon” driveability rating: Depending on which module failed, anything from a dead accessory to a no-start is possible - find out which module before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
multiple warning lights on at once
systems controlled by that module not working
module not responding to the scan tool
car in limp mode or won't start
code returns immediately after clearing
Likely causes
Internal electronic failure in the module itself (most common once power and wiring are ruled out)
Low or unstable supply voltage making the module misbehave during its self-check
Corroded connector, bad ground, or water intrusion at the module
Corrupted software from a failed or interrupted module update
Physical damage to the module from heat, vibration, or previous accident work
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Identify exactly which module set the code - 'control module' alone doesn't name the culprit.
Rule out power and ground first: check the module's fuses, its power feeds, and its ground points.
Inspect the module's connector for corrosion, water, or pushed-back pins. Tests: Corroded connector, bad ground, or water intrusion at the module
Check for software updates or service bulletins - some U3000 variants are fixed by a reflash, not a replacement. Tests: Corrupted software from a failed or interrupted module update
If power, ground, wiring, and software all check out, the module itself has failed - replace it and program it to the vehicle.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$345 – $2880
Labor$150 – $850
Control module replacement with programming. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U3000 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Proving a module is truly dead needs a factory-level scan tool and a wiring diagram; replacement modules almost always need dealer or locksmith programming.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →