Diagnose soonDepending on which module failed, anything from a dead accessory to a no-start is possible - find out which module before driving far.
One of your car's computer modules failed its own internal self-test. It may genuinely be bad, but weak power, a bad ground, or a corroded connector can make a healthy module look broken - so check power and wiring before buying a module.
Key facts
U3000 means control Module. One of your car's computer modules failed its own internal self-test. It may genuinely be bad, but weak power, a bad ground, or a corroded connector can make a healthy module look broken - so check power and wiring before buying a module. WrenchFair's published fair-price range for this repair is $345–$2880 parts and $150–$850 labor at independent shops.
WrenchFair rates U3000 a 5-of-5 DIY difficulty (“Proving a module is truly dead needs a factory-level scan tool and a wiring diagram; replacement modules almost always need dealer or locksmith programming.”) with a “Diagnose soon” driveability rating: Depending on which module failed, anything from a dead accessory to a no-start is possible - find out which module before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2024–2024 GMC Hummer EV (all) — Rear steering inoperative after programming (PIT6350):Factory-documented
No owner procedure; the SDAC programming is dealer equipment. If rear steering dies and Super Cruise goes with it on a 2024, don't keep driving it hard; get it to the dealer for the programming sequence.
Do this test first: Identify exactly which module set the code - 'control module' alone doesn't name the culprit.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for U3000 on the 2024–2024 GMC Hummer EV — but the community-sourced Rear steering inoperative after programming (PIT6350) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Tips
GM preliminary information PIT6350 (March 2025) covers 2024 Hummer EV pickups and SUVs: rear steering goes inoperative with DTC U3000 symptom byte 49 plus U1962 or U1961 symptom byte 92 set in the K92 rear power steering control module.
There may be no warning message at all; Super Cruise operation is disabled and the steering wheel can sit off-center. The cause is that Serial Data Authentication (SDAC) never ran after vehicle-wide programming, so the module sets the codes.
The dealer correction is specific: disconnect the 12V negative cable only after confirming Battery Maintenance Mode is inactive (it can be active with the ignition off and the cord unplugged, and disconnecting live can shock or burn), wait 30 minutes, reconnect, then run SDAC immediately; repeat SDAC if it fails.
Typical difficulty: Moderate — based on 1374 code guides for the electrical repair area (an area-level estimate, not this exact job).
Typical time: “The dealer correction is specific: disconnect the 12V negative cable only after confirming Battery Maintenance Mode is inactive (it can be active with the ignition off and the cord unplugged, and disconnecting live can…” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
multiple warning lights on at once
systems controlled by that module not working
module not responding to the scan tool
car in limp mode or won't start
code returns immediately after clearing
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Internal electronic failure in the module itself (most common once power and wiring are ruled out)
Low or unstable supply voltage making the module misbehave during its self-check
Corroded connector, bad ground, or water intrusion at the module
Corrupted software from a failed or interrupted module update
Physical damage to the module from heat, vibration, or previous accident work
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Identify exactly which module set the code - 'control module' alone doesn't name the culprit.
Rule out power and ground first: check the module's fuses, its power feeds, and its ground points.
Inspect the module's connector for corrosion, water, or pushed-back pins. Tests: Corroded connector, bad ground, or water intrusion at the module
Check for software updates or service bulletins - some U3000 variants are fixed by a reflash, not a replacement. Tests: Corrupted software from a failed or interrupted module update
If power, ground, wiring, and software all check out, the module itself has failed - replace it and program it to the vehicle.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2024–2024 GMC Hummer EV: Rear steering inoperative after programming (PIT6350) — test first, then buy for this job.
The price range below is a national planning range for U3000 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$345 – $2880
Labor$150 – $850
Control module replacement with programming. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U3000 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Proving a module is truly dead needs a factory-level scan tool and a wiring diagram; replacement modules almost always need dealer or locksmith programming.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →