Diagnose soonBad data from the engine computer can trigger reduced power or stalling — get it diagnosed before a long trip.
Your car has a dozen-plus small computers that constantly share data. The engine computer is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can make the car run badly, shift harshly, or lose power.
Key facts
U0401 means invalid Data Received From ECM/PCM A. Your car has a dozen-plus small computers that constantly share data. The engine computer is sending messages that don't make sense — impossible numbers, frozen values, or garbled frames — so the other computers are ignoring it. That can make the car run badly, shift harshly, or lose power. WrenchFair's published fair-price range for this repair is $600–$1500 parts and $200–$400 labor at independent shops.
WrenchFair rates U0401 a 2-of-5 DIY difficulty (“Checking the battery, connectors, and wiring is solid DIY work; condemning or replacing the module itself usually isn't.”) with a “Diagnose soon” driveability rating: Bad data from the engine computer can trigger reduced power or stalling — get it diagnosed before a long trip. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2017 Jeep Patriot (2.0L World I4, 2.4L World I4) — Lightning-bolt light / limp mode:Owner-verified
The throttle body sits on the intake manifold, reachable from above with basic hand tools. Budget 30-60 minutes for the swap; plan a relearn right after.
Do this test first: Test the battery and charging system first — low or unstable voltage is the most common cause of garbage data on the network.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for U0401 on the 2007–2017 Jeep Patriot — but the community-sourced Lightning-bolt light / limp mode note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Throttle body mounting bolts: verify — Torque specs for the throttle body bolts not confirmed from a forum source — confirm against factory service info before torquing.
Tips
The red lightning bolt on the dash is the electronic throttle control warning. When it comes on with limp mode and no acceleration, the throttle body is the prime suspect: a YouTube owner scanned throttle-body codes on his Patriot, replaced the throttle body, and reports the bolt went away and full throttle response came back.
Buy the OEM throttle body, not the cheapest aftermarket one. Multiple technicians answering Patriot ETC questions warn that aftermarket units are finicky and often throw the same codes right out of the box, turning a one-afternoon job into a repeat.
A proper ETC relearn after the swap matters. On these Patriots the relearn needs a bi-directional scan tool; several owners tried the key-on-and-pump-the-pedal trick and found the light stayed on or came right back until a shop did the relearn. Budget for a shop visit or a capable scan tool if the light persists.
If the bolt comes back with no codes stored, inspect the throttle body connector and the wiring before condemning a second throttle body. A 2013 Patriot owner's thread shows the aftermarket body lit the bolt with zero codes; the connector and relearn were part of the fix.
Check engine codes help steer this: P2173 (high airflow detected) points at the throttle body, MAP sensor, or engine computer, and U0401 indicates lost communication with the throttle actuator module rather than a dead throttle body.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
Typical time: “Budget 30-60 minutes for the swap; plan a relearn right after.” — as written in the note. First-timers often take twice this.
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
reduced power or limp mode
harsh or delayed shifting
other modules log the same code
stalling or hard starting in severe cases
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
weak battery or failing alternator corrupting network data
corroded or loose connector at the engine computer
damaged wiring or poor ground to the engine computer
a sensor feeding the engine computer reporting bad values
software/calibration mismatch after a repair
internal fault in the engine computer
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Test the battery and charging system first — low or unstable voltage is the most common cause of garbage data on the network. Tests: weak battery or failing alternator corrupting network data
Scan every module on the vehicle and record all codes; pay special attention to any faults the engine computer reports about itself or its own sensors. Tests: a sensor feeding the engine computer reporting bad values
Inspect the engine computer's connector and wiring for corrosion, loose or pushed-back pins, water intrusion, or rodent damage, and verify its power and ground feeds. Tests: corroded or loose connector at the engine computer
Clear all codes, drive normally, and rescan — if this code returns together with the engine computer's own sensor or input codes, fix those inputs first, since bad data in means bad data out. Tests: a sensor feeding the engine computer reporting bad values
If power, ground, and wiring all test good and the engine computer keeps broadcasting implausible values, the module itself is suspect — replacement or reprogramming is usually a dealer or specialist job.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2017 Jeep Patriot: Lightning-bolt light / limp mode — test first, then buy for this job.
The price range below is a national planning range for U0401 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$600 – $1500
Labor$200 – $400
Repairing the wiring or connector at the engine computer, or replacing the module. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U0401 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Checking the battery, connectors, and wiring is solid DIY work; condemning or replacing the module itself usually isn't.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →