U024C: Lost communication with Seat control module H
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeOnly a comfort or convenience feature is affected — the car is safe to drive; fix it when convenient.
Your car's computers all chat over a shared wiring network. Right now, the seat control module h — the part that handles power seat adjustment and memory — has stopped answering. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module.
Key facts
U024C means lost communication with Seat control module H. Your car's computers all chat over a shared wiring network. Right now, the seat control module h — the part that handles power seat adjustment and memory — has stopped answering. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module. WrenchFair's published fair-price range for this repair is $0–$600 parts and $120–$300 labor at independent shops.
WrenchFair rates U024C a 2-of-5 DIY difficulty (“Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.”) with a “Drive safe” driveability rating: Only a comfort or convenience feature is affected — the car is safe to drive; fix it when convenient. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
power seat adjustment and memory not working
warning light on the dash (check engine, abs, or a module-specific message)
related features dead, intermittent, or stuck
companion communication codes stored in other modules
Likely causes
Blown fuse or corroded fuse holder feeding the seat control module h (most common easy fix — check the fuses first)
Loose, corroded, or water-damaged connector at the seat control module h
Chafed, pinched, or broken data-bus wiring running to the seat control module h
Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker, plug-in insurance dongle)
The seat control module h failed internally (possible but uncommon — rule out power and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module. Tests: The seat control module h failed internally (possible but uncommon — rule out power and…
Check the fuses for the seat control module h using the owner's manual fuse chart. A blown, corroded, or loose fuse is the cheapest possible cause — don't skip this step. Tests: Blown fuse or corroded fuse holder feeding the seat control module h (most common easy…
Unplug the connector at the seat control module h and verify its power and ground with a multimeter. Look closely for green corrosion, backed-out pins, or water inside the connector — most 'dead module' diagnoses turn out to be bad connections. Tests: Loose, corroded, or water-damaged connector at the seat control module h
Trace the data-bus wiring to the seat control module h: look for chafed or pinched harness runs, water intrusion at connectors, and aftermarket devices (alarms, remote starters, trackers) tapped into the bus. Tests: Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker,…
If power, ground, and wiring all check out, the module itself may have failed — but replacement modules usually need programming to the vehicle, so confirm the wiring first and get a second opinion before buying one.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$0 – $600
Labor$120 – $300
Blown fuse or wiring repair (most common). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U024C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →