U019D

U019D: Lost communication with Direct ozone reduction catalyst temperature sensor

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Your car's computers all chat over a shared wiring network. Right now, the direct ozone reduction catalyst temperature sensor — the part that handles catalyst temperature monitoring (emissions) — has stopped answering. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module. Tests: The direct ozone reduction catalyst temperature sensor failed internally (possible but…
  2. Check the fuses for the direct ozone reduction catalyst temperature sensor using the owner's manual fuse chart. A blown, corroded, or loose fuse is the cheapest possible cause — don't skip this step. Tests: Blown fuse or corroded fuse holder feeding the direct ozone reduction catalyst…
  3. Unplug the connector at the direct ozone reduction catalyst temperature sensor and verify its power and ground with a multimeter. Look closely for green corrosion, backed-out pins, or water inside the connector — most 'dead module' diagnoses turn out to be bad connections. Tests: Loose, corroded, or water-damaged connector at the direct ozone reduction catalyst…
  4. Trace the data-bus wiring to the direct ozone reduction catalyst temperature sensor: look for chafed or pinched harness runs, water intrusion at connectors, and aftermarket devices (alarms, remote starters, trackers) tapped into the bus. Tests: Chafed, pinched, or broken data-bus wiring running to the direct ozone reduction catalyst…
  5. If power, ground, and wiring all check out, the module itself may have failed — but replacement modules usually need programming to the vehicle, so confirm the wiring first and get a second opinion before buying one.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$0 – $250
Labor$120 – $300

Blown fuse or wiring repair (most common). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U019D ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.

Watch this repair on YouTube

Parts & tools

Electrical diagnosis toolkit — what the job actually takes

Torque specs: Module connectors: hand-tight until they click — never force them.

Pro tip: Check powers AND grounds before condemning a module — most “module failures” are wiring. Disconnect the battery before unplugging modules.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →