U013C: Lost communication with Accelerator pedal module
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car usually still drives, but the offline module's functions are unavailable — get it checked before they matter.
Your car's computers all chat over a shared wiring network. Right now, the accelerator pedal module — the part that handles throttle response — has stopped answering. The engine may drop into limp mode. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module.
Key facts
U013C means lost communication with Accelerator pedal module. Your car's computers all chat over a shared wiring network. Right now, the accelerator pedal module — the part that handles throttle response — has stopped answering. The engine may drop into limp mode. Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module. WrenchFair's published fair-price range for this repair is $0–$600 parts and $120–$300 labor at independent shops.
WrenchFair rates U013C a 2-of-5 DIY difficulty (“Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.”) with a “Diagnose soon” driveability rating: The car usually still drives, but the offline module's functions are unavailable — get it checked before they matter. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
throttle response not working
warning light on the dash (check engine, abs, or a module-specific message)
related features dead, intermittent, or stuck
companion communication codes stored in other modules
Likely causes
Blown fuse or corroded fuse holder feeding the accelerator pedal module (most common easy fix — check the fuses first)
Loose, corroded, or water-damaged connector at the accelerator pedal module
Chafed, pinched, or broken data-bus wiring running to the accelerator pedal module
Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker, plug-in insurance dongle)
The accelerator pedal module failed internally (possible but uncommon — rule out power and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module. Tests: The accelerator pedal module failed internally (possible but uncommon — rule out power…
Check the fuses for the accelerator pedal module using the owner's manual fuse chart. A blown, corroded, or loose fuse is the cheapest possible cause — don't skip this step. Tests: Blown fuse or corroded fuse holder feeding the accelerator pedal module (most common easy…
Unplug the connector at the accelerator pedal module and verify its power and ground with a multimeter. Look closely for green corrosion, backed-out pins, or water inside the connector — most 'dead module' diagnoses turn out to be bad connections. Tests: Loose, corroded, or water-damaged connector at the accelerator pedal module
Trace the data-bus wiring to the accelerator pedal module: look for chafed or pinched harness runs, water intrusion at connectors, and aftermarket devices (alarms, remote starters, trackers) tapped into the bus. Tests: Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker,…
If power, ground, and wiring all check out, the module itself may have failed — but replacement modules usually need programming to the vehicle, so confirm the wiring first and get a second opinion before buying one.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$0 – $600
Labor$120 – $300
Blown fuse or wiring repair (most common). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U013C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →