U0101

u0101 on a 2012–2018 Ford Focus: Lost communication with TCM

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: U0101 on a 2006–2016 Chevrolet 2500 · 2011–2019 Ford Fiesta · 2012–2018 Ford Focus

DIY difficulty 2/5

Your car's computers all chat over a shared wiring network. Right now, the transmission computer (TCM) — the part that handles transmission control — has stopped answering. The transmission may be stuck in one gear (limp mode). Check the simple stuff first: a blown fuse or a loose, corroded connector is a far more common cause than a dead module.

Key facts

☑ Before you buy parts — check these first:
On your 2012–2018 Ford Focus (2.0L I4 (GDI Duratec Ti-VCT)) — TCM failure — sudden neutral/limp mode, 14M02 10yr/150k coverage: Owner-verified
Driveway-able: unbolt the old TCM from the transmission and swap it. The adaptive-learning step needs Ford IDS, FORScan with extended license, or a shop visit.
Do this test first: Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for u0101 on the 2012–2018 Ford Focus — but the community-sourced TCM failure — sudden neutral/limp mode, 14M02 10yr/150k coverage note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: Focus Fanatics: PowerShift dual-clutch TCM failure symptoms thread — 14M02 coverage discussion and owner failure reports · YouTube: How to replace the TCM in a 2012-2018 Ford Focus 2.0L, incl. TCM adaptive learning with Ford IDS

Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to U0101: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 5 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Read all codes with a scan tool. This code is set by a listening module, not the silent one — note any companion codes naming other offline modules or bus faults, which point at shared power or wiring instead of one bad module. Tests: The transmission computer (TCM) failed internally (possible but uncommon — rule out power…
  2. Check the fuses for the transmission computer (TCM) using the owner's manual fuse chart. A blown, corroded, or loose fuse is the cheapest possible cause — don't skip this step. Tests: Blown fuse or corroded fuse holder feeding the transmission computer (TCM) (most common…
  3. Unplug the connector at the transmission computer (TCM) and verify its power and ground with a multimeter. Look closely for green corrosion, backed-out pins, or water inside the connector — most 'dead module' diagnoses turn out to be bad connections. Tests: Loose, corroded, or water-damaged connector at the transmission computer (TCM)
  4. Trace the data-bus wiring to the transmission computer (TCM): look for chafed or pinched harness runs, water intrusion at connectors, and aftermarket devices (alarms, remote starters, trackers) tapped into the bus. Tests: Aftermarket device tapped into the data bus (remote starter, alarm, fleet tracker,…
  5. If power, ground, and wiring all check out, the module itself may have failed — but replacement modules usually need programming to the vehicle, so confirm the wiring first and get a second opinion before buying one.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2012–2018 Ford Focus: TCM failure — sudden neutral/limp mode, 14M02 10yr/150k coverage — test first, then buy for this job.
The price range below is a national planning range for u0101 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$0 – $1200
Labor$120 – $300

Blown fuse or wiring repair (most common). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for U0101 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Finding a blown fuse or bad connector is easy; tracing bus wiring to the module is the part that takes patience.

Watch this repair on YouTube

Parts & tools

Electrical diagnosis toolkit — what the job actually takes

Torque specs: Module connectors: hand-tight until they click — never force them.

Pro tip: Check powers AND grounds before condemning a module — most “module failures” are wiring. Disconnect the battery before unplugging modules.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →