P3470: Cylinder 9 exhaust valve control circuit Range/Performance
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonIf the engine is actively misfiring, don't ignore it - unburned fuel can overheat and damage the catalytic converter; otherwise this is a fuel-economy and smoothness issue to fix soon.
Your engine has a system that rests cylinder 9 to save fuel on the highway, using a small oil-driven valve on the exhaust side. The computer found an electrical problem in that valve's wiring - a degrading solenoid, corroded connector adding resistance, or sluggish oil flow. Check the oil first, because low or dirty oil is the most common reason these codes appear.
Key facts
P3470 means cylinder 9 exhaust valve control circuit Range/Performance. Your engine has a system that rests cylinder 9 to save fuel on the highway, using a small oil-driven valve on the exhaust side. The computer found an electrical problem in that valve's wiring - a degrading solenoid, corroded connector adding resistance, or sluggish oil flow. Check the oil first, because low or dirty oil is the most common reason these codes appear. WrenchFair's published fair-price range for this repair is $40–$180 parts and $150–$500 labor at independent shops.
WrenchFair rates P3470 a 3-of-5 DIY difficulty (“Electrical diagnosis is straightforward with a multimeter, but reaching the solenoid can mean removing the intake manifold on some engines.”) with a “Diagnose soon” driveability rating: If the engine is actively misfiring, don't ignore it - unburned fuel can overheat and damage the catalytic converter; otherwise this is a fuel-economy and smoothness issue to fix soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
engine misfire (the ecm may disable that cylinder's injector)
chafed, burnt, or broken wiring in the cylinder 9 control circuit
corroded or loose connector at the solenoid
defective ecm (rare - rule out oil and wiring first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Check the engine oil level and condition first - low, dirty, or wrong-viscosity oil is the top cause of deactivation codes; correct it, clear the code, and retest. Tests: low engine oil level or pressure
2. Research TSBs for your year, model, and engine - some deactivation faults are known issues with a published fix. Tests: failed cylinder 9 exhaust-side deactivation solenoid
3. Locate the cylinder 9 exhaust-side deactivation solenoid and inspect its wiring and connector for chafing, burns, corrosion, or loose pins. Tests: failed cylinder 9 exhaust-side deactivation solenoid
4. Compare the solenoid's response against the vehicle service procedure - a coil drifting out of spec or a valve responding sluggishly points at the solenoid or restricted oil flow. Tests: restricted oil passage to the solenoid
5. If the circuit tests good, replace the solenoid and clear any blocked oil passages; retest before condemning anything else.
6. Suspect the ECM only after oil, wiring, and the solenoid are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $180
Labor$150 – $500
Replacing the faulty cylinder deactivation solenoid, after ruling out oil level and wiring. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P3470 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Electrical diagnosis is straightforward with a multimeter, but reaching the solenoid can mean removing the intake manifold on some engines.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →