Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThis is an emissions fault, not a breakdown risk - but it will fail an inspection, so fix it before your test.
Your fuel vapor system has a small pump that tests the system for leaks, and that pump is not behaving - stuck on.
Key facts
P2DDB means eVAP System Leak Detection Pump Stuck On. Your fuel vapor system has a small pump that tests the system for leaks, and that pump is not behaving - stuck on. WrenchFair's published fair-price range for this repair is $60–$250 parts and $100–$250 labor at independent shops.
WrenchFair rates P2DDB a 2-of-5 DIY difficulty (“Pump swaps are usually one connector and a hose or two; the smoke test is what separates a bad pump from a real leak.”) with a “Diagnose soon” driveability rating: This is an emissions fault, not a breakdown risk - but it will fail an inspection, so fix it before your test. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
faint fuel smell near the car
failed emissions inspection
pump running constantly or never running
possible smell of fuel near tank or engine bay
loose-cap warning may appear
Likely causes
Worn-out pump motor (most common)
Clogged pump filter or reference orifice
Cracked hose or loose connection at the pump
Failed pump driver in the control module (rare)
relay contacts welded
output driver stuck on
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code and check the gas cap first - a loose cap mimics pump faults on some systems. Tests: Cracked hose or loose connection at the pump
Command the pump with a scan tool and listen for it running.
Inspect the pump, its filter, and hoses for cracks, clogs, or rodent damage. Tests: Clogged pump filter or reference orifice
Smoke-test the EVAP system to rule out a real leak making the pump look bad.
Replace the pump if it will not run or runs constantly, then run the system's self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $250
Labor$100 – $250
EVAP leak detection or purge pump replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2DDB ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Pump swaps are usually one connector and a hose or two; the smoke test is what separates a bad pump from a real leak.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →