P0442

P0442: Evaporative emission control system leak detected (small leak)

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

DIY difficulty 1/5

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0442 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

At a glance

What it meansSmall leak in the system that captures fuel vapors. Nine times out of ten it's the gas cap - check that first.
Most common causeLoose or cracked gas cap (check first, always)
Can you drive?Yes.
SeverityLow
DIY cost (parts only)$15 – $500
Shop cost (parts + labor)$15 – $900
DIY difficulty1 of 5 — Gas cap first; smoke test if it persists.

Can I drive with P0442?

Can I drive with a P0442 code?

Yes. P0442 doesn't make your car unsafe to drive on its own. Emissions-only fault. Safe to drive - often just the gas cap. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0442?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions-only fault. Safe to drive - often just the gas cap.

Will P0442 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

More detail: can I drive with P0442? →

Will P0442 fail an emissions inspection?

Yes, if your state or county runs an OBD-II emissions test and the check-engine light is on. The test plugs into your car's computer, and under the EPA's OBD inspection criteria any code that commands the light on is itself a failure — no tailpipe reading needed.

Fixing the fault is only half the job. Clearing the code resets every readiness monitor, and they have to run again before the car will pass. The EVAP monitor is often the last to set — it only runs under specific conditions — so don't clear codes the week of your test. See the drive-cycle and readiness guide →

One break for EVAP codes: the EVAP monitor is the single monitor California excuses on 2000-and-newer gasoline vehicles, and in states following the EPA's allowance (up to two monitors not ready for 1996–2000, one for 2001 and newer) it can be your one allowed incomplete monitor. But that excuses an incomplete monitor, not a lit light — while this code is active and the light is on, the car still fails.

Not everywhere tests: some states have no emissions test at all (South Carolina is one), and in others only certain counties test — so there, this code alone won't block registration. Rules vary by county as well as state, and they change, so confirm with your state's DMV before test day.

Small leak in the system that captures fuel vapors. Nine times out of ten it's the gas cap - check that first.

VCDS tip: Clear the code after a gas-cap fix and complete two drive cycles before retesting.
Model notes: Tighten or replace the gas cap and drive two full drive cycles before doing anything else - this fixes it more often than not. Brand patterns: on Volvos the leak detection pump is a common culprit; on Chrysler/Jeep it is the ESIM module; on Hyundai and GM the purge valve.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 3 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Tighten/replace the gas cap and drive two cycles before anything else
  2. Smoke-test the EVAP system
  3. Command the vent valve closed in output tests Tests: Leaking purge or vent valve

Typical price range

Parts$15 – $500
Labor$0 – $400

A gas cap is under $25, but a real shop bill — a $60-$150 smoke test plus a purge/vent valve at $150-$400 installed, or a canister at $300-$700+ installed — typically lands $200-$400. The ranges above span all paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

DIY difficulty

1 of 5 — Gas cap first; smoke test if it persists.

Parts & tools

Related codes

🔍 Seeing multiple codes? Combinations mean something different than codes alone. How to read code combinations →
Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →