P2C3C: Cylinder Head Temperature Sensor B Circuit Intermittent/Erratic
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThis sensor is the overheat last line of defense - verify the engine is truly cool before assuming it is just the sensor.
Your engine has a sensor reading the cylinder head's metal temperature directly - the last line of defense against overheating damage - and it is giving a bad reading. Usually the sensor or its wiring in the hot cylinder head area.
Key facts
P2C3C means cylinder Head Temperature Sensor B Circuit Intermittent/Erratic. Your engine has a sensor reading the cylinder head's metal temperature directly - the last line of defense against overheating damage - and it is giving a bad reading. Usually the sensor or its wiring in the hot cylinder head area. WrenchFair's published fair-price range for this repair is $40–$150 parts and $100–$250 labor at independent shops.
WrenchFair rates P2C3C a 3-of-5 DIY difficulty (“The critical step is ruling out a real overheat first; the sensor swap itself is usually accessible.”) with a “Diagnose soon” driveability rating: This sensor is the overheat last line of defense - verify the engine is truly cool before assuming it is just the sensor. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
temperature gauge reading oddly
possible overheat protection limiting power
cooling fans running hard
Likely causes
Failed cylinder head temperature sensor B (most common)
Heat-damaged wiring or corroded connector
Actual overheating skewing the reading (verify real temperature first)
Control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
Verify the engine is not actually overheating - check coolant level and look for leaks first. Tests: Actual overheating skewing the reading (verify real temperature first)
Inspect the sensor wiring and connector for heat damage. Tests: Heat-damaged wiring or corroded connector
Compare the sensor reading against coolant temperature and a plausible value. Tests: Failed cylinder head temperature sensor B (most common)
Replace the sensor if it reads wrong, clear the code, and confirm the reading tracks reality.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $150
Labor$100 – $250
Cylinder head temperature sensor B replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2C3C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The critical step is ruling out a real overheat first; the sensor swap itself is usually accessible.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →