Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe alt-fuel system simply stays off while this fault is present - safe to drive on gasoline.
The computer that runs your CNG/LPG system gets its power through a relay, and the relay circuit has an electrical fault (sense circuit high). When the alt-fuel computer loses power, the system just stays on gasoline. Often it is the relay itself, a blown fuse, or corroded wiring.
Key facts
P2A37 means aFCM Power Relay Sense Circuit High. The computer that runs your CNG/LPG system gets its power through a relay, and the relay circuit has an electrical fault (sense circuit high). When the alt-fuel computer loses power, the system just stays on gasoline. Often it is the relay itself, a blown fuse, or corroded wiring. WrenchFair's published fair-price range for this repair is $20–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P2A37 a 2-of-5 DIY difficulty (“Relay and fuse work is beginner-level; tracing the sense circuit takes a multimeter and the wiring diagram.”) with a “Diagnose soon” driveability rating: The alt-fuel system simply stays off while this fault is present - safe to drive on gasoline. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
alt-fuel system warning light on
vehicle will not switch to alternative fuel
intermittent alt-fuel operation
stuck running on gasoline only
Likely causes
Failed AFCM power relay (most common - contacts burn with age)
Blown fuse in the AFCM power feed
Corroded or loose wiring/connector in the relay circuit
AFCM internal power fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
Check the AFCM fuses first, then swap the AFCM relay with a known-good identical relay as a quick test. Tests: Failed AFCM power relay (most common - contacts burn with age)
Inspect the relay socket and wiring for corrosion, heat damage, or loose terminals. Tests: Corroded or loose wiring/connector in the relay circuit
Test the relay control and sense circuits per the factory service manual. Tests: Corroded or loose wiring/connector in the relay circuit
Replace the relay or repair the wiring, clear the code, and confirm the AFCM powers up reliably.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$20 – $120
Labor$80 – $200
AFCM power relay or fuse replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2A37 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Relay and fuse work is beginner-level; tracing the sense circuit takes a multimeter and the wiring diagram.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →