P2A0D: Manifold absolute pressure sensor B circuit high
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe engine runs on estimated airflow while this code is active - driveable, but fix it before performance or economy complaints grow.
Your engine has a second intake-pressure sensor (MAP B), and the computer found a high signal on it. The engine still runs, but it is guessing at airflow instead of measuring it, so expect slightly worse performance and economy until it is fixed.
Key facts
P2A0D means manifold absolute pressure sensor B circuit high. Your engine has a second intake-pressure sensor (MAP B), and the computer found a high signal on it. The engine still runs, but it is guessing at airflow instead of measuring it, so expect slightly worse performance and economy until it is fixed. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$160 labor at independent shops.
WrenchFair rates P2A0D a 2-of-5 DIY difficulty (“MAP sensors are usually one bolt and one connector; the real work is the diagnosis, which is scan-tool and multimeter work.”) with a “Diagnose soon” driveability rating: The engine runs on estimated airflow while this code is active - driveable, but fix it before performance or economy complaints grow. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
reduced engine performance
rough idle or hesitation
increased fuel consumption
Likely causes
Signal wire shorted to power or sensor element open (most common)
MAP B sensor failed internally
Connector pins corroded or pushed back
Chafed harness shorting to a power wire
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Read the code with a scan tool and save the freeze-frame data, then check for companion codes - when several sensor codes appear together, suspect a shared reference-voltage or ground problem before any single sensor.
Locate MAP sensor B (bank 2 side or secondary intake - confirm in the service manual) and inspect its connector, wiring, and vacuum hose for cracks, kinks, or disconnection. Tests: Connector pins corroded or pushed back
Compare MAP B live data against MAP A (or calculated load) at key-on-engine-off and at idle - a large disagreement points at the sensor or its plumbing.
Wiggle-test the harness with the engine running; if the reading jumps, repair the wiring rather than replacing the sensor.
Replace the sensor if the wiring and plumbing check out, then clear the code and verify the readings agree on a test drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $120
Labor$80 – $160
MAP sensor B replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2A0D ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — MAP sensors are usually one bolt and one connector; the real work is the diagnosis, which is scan-tool and multimeter work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →